توضیحات
ABSTRACT
Many different types of branching have been developed, such as bifurcation, trifurcation, and manifolds, among others. These configurations are used in penstocks to transport water from surge tanks to power ouses in order to feed several turbines at the same time. This arrangement allows for smaller ssembly costs in comparison with independent penstock systems. Nevertheless, such installations can enerate higher head losses in the system in comparison with single systems. This study focuses on the quantification of these head losses as a function of volumetric flow rate using Computational Fluid ynamics (CFD) and later validated with previously published results. To determine the coefficient of head losses three mesh settings were analyzed: hexahedral, tetrahedral and hybrid, for both a steady state and transitory flow. Based on the literature, the k-ω turbulence model was used, with refinement to elements near the wall to check y+. To the simulation transitory, the SAS model was used for nalysis
of the instability in the trifurcation.
INTRODUCTION
Extensive research has been carried out in order to quantify losses in adduction systems, particularly in the high pressure components of hydroelectric plants in order to maximize their performance. Common types of branching seen in studies are bifurcations, while a few studies have looked into trifurcations in penstocks. This can be attributed to the uneven flow at the turbine entrances and higher variable loss oefficients. It is important to note that turbine performance depends on the flow behavior on the enstock, and therefore the research on trifurcations could be made through numerical or experimental nalyses to provide vital information for an appropriate turbine design. In hydroelectric plants that only use one penstock, it is essential to use branches for the flow distribution of the hydraulic machines. Three geometric configurations of the ramifications are mainly used in penstocks; bifurcations, rifurcations and manifolds. The bifurcations and trifurcations can be classified into two categories based on the geometry employed, considering the structural advantages. The first geometrical rrangement is comprised by trunk cones which intersect in the middle of the branches, while the second geometry uses a sphere between at the branches.
چکیده
بسیاری از انواع شاخه های مختلف مانند بفرگکتیو، تروریزاسیون و منیفولد ها، از جمله دیگر توسعه یافته اند. این تنظیمات برای جلوگیری از حمل و نقل آب از مخازن پرتقال به نیروگاه ها به منظور انتقال چندین توربین در یک زمان استفاده می شود. این ترتیب هزینه های ساختاری کوچکتر را در مقایسه با سیستم های مستقل پنوماتیک امکان پذیر می سازد. با این وجود، چنین تاسیساتی می توانند در سیستم نسبت به سیستم های واحد آسیب بالاتری ایجاد کنند. این مطالعه بر اندازه گیری میزان خسارات سر به عنوان تابعی از سرعت جریان حجمی با استفاده از سی ان سی سیالات محاسباتی (CFD) تمرکز دارد و بعد از آن با نتایج منتشر شده تأیید شده است. برای تعیین ضریب تلفات سر و صدا سه تنظیمات مش مورد بررسی قرار گرفت: شش گوشه، تتراگرام و هیبرید، برای هر دو حالت پایدار و جریان گذرا. بر اساس ادبیات، مدل توربولانس k-ω با استفاده از پالایش به عناصر در نزدیکی دیوار برای بررسی y + استفاده شد. برای گذر شبیه سازی، مدل SAS برای nalysis مورد استفاده قرار گرفت
از بی ثباتی در trifurcation.
مقدمه
تحقیقات گسترده ای برای اندازه گیری تلفات در سیستم های adduction، به ویژه در اجزای فشار بالا از گیاهان برق آبی، به منظور به حداکثر رساندن عملکرد آنها انجام شده است. انواع مختلف شاخه ای که در مطالعات دیده می شوند، بیبورکاسیون هستند، در حالیکه چندین مطالعه به سهولت در قلم افتاده است. این را می توان به جریان ناهموار در ورودی های توربین و ضریب افت تغییر متغیر بیشتر نسبت داد. مهم است که توجه داشته باشیم که عملکرد توربین به رفتار جریان در انستاک بستگی دارد و بنابراین تحقیق در مورد trifurcations می تواند از طریق nalyses عددی یا تجربی برای ارائه اطلاعات حیاتی برای طراحی مناسب توربین ساخته شود. در گیاهان هیدرو الکتریکی که فقط از یک پنستاک استفاده می کنند، استفاده از شاخه ها برای توزیع جریان ماشین های هیدرولیکی ضروری است. سه شکل هندسی از تأثیرات عمدتا در مجاورت قلمه ها استفاده می شود؛ bifurcations، rifurcations و چند منظوره. با توجه به مزایای ساختاری، دوچرخه ها و سهگانه ها را می توان به دو دسته طبقه بندی کرد. نخستین ترتیب هندسی شامل مخروط های تنه ای است که در وسط شاخه ها متقابل هستند، در حالی که هندسه دوم از شاخه ای بین شاخه ها استفاده می کند.
Year: 2019
Publisher : ELSEVIER
By : Carlos Andrés Aguirre, Ramiro Gustavo Ramirez Camacho, Waldir de Oliveira,François Avellan
File Information: English Language/ 18 Page / size: 1.25 MB
سال : 1397
ناشر : ELSEVIER
کاری از : کارلوس اندرس آگیرر، رامیرو گوستاو رامیرز کاماچو، ولدیر د الیویرا، فرانسوا آولان
اطلاعات فایل : زبان انگلیسی / 18 صفحه / حجم : MB 1.25
نقد و بررسیها
هنوز بررسیای ثبت نشده است.