توضیحات
چکیده
در بسياري از سازه هاي فلزي مانند تيرهاي لانه زنبورهاي شيارهاي -Vشكلي وجود دارند. در اثر تمركز تنش شديد در اطراف اين شيارها كه ناشي از بار برشي ايجاد شده بواسطة خمش در محور خنثي آنها ميباشد و به علت رفتار تغيير فرم پذير فلزات، يك ناحية پلاستيك در اطراف اين شيارها تشكيل ميشود كه شكل و اندازة آن اثر شايان توجهي بر روي رفتار شكست سازه و واماندگي آن دارد. در اين مقاله ناحية پلاستيك براي شيارهايي با زاوية دهانة متفاوت در دو حالت تنش و كرنش صفحهاي در بارگذاري برشي خالص (مودII ) بررسي شده و رابطه اي تحليلي براي شعاع بي بعد ناحية پلاستيك اطراف شيارها ارائه گرديده است. از جمله پارامترهاي مهم در بررسي ناحية پلاستيك، مساحت ناحية پلاستيك و اندازة آن در امتداد محور شيار ميباشد. نتايج بدست آمده نشان مي دهد كه شكل ناحية پلاستيك براي شيارها شبيه شكل اين ناحيه براي تركها ميباشد و براي تمامي زواياي دهانة شيار تغيير حالت از تنش به كرنش صفحه اي بر روي شكل ناحية پلاستيك روبروي شيار تأثير چنداني نداشته، بيشتر ناحية پلاستيك پشت شيار را تحت تأثير قرار داده است به صورتيكه با افزايش ضريب پوآسون مساحت اين ناحيه به مقدار بسيار كمي كاهش پيدا كرده است. همچنين مشاهده ميشود كه در مود IIبارگذاري، افزايش ضريب پوآسون تغييري در شعاع ناحية پلاستيك در امتداد محور شيار ايجاد نميكند.
مقدمه
در سازه هاي فلزي بعضاً تركها و شيارهايي در مرحلة ساخت و يا به دليل عيبهاي موجود، بتدريج در طول دوره كاري سازه بر اثر بارهاي اعمالي ايجاد ميشود. به عنوان نمونه در پل هاي فلزي بر اثر حركت وسايل نقليه، در پوسته هاي جدار نازك مورد استفاده در مخازن تحت فشار بر اثر كم و ياد شدن فشار داخل مخزن، در دكل هاي برق بر اثر جريان باد و همينطور در بسياري از ديگر سازه هاي مهندسي بر اثر بارهاي خستگي، تركها و شيارهايي در نواحي تمركز تنش تشكيل ميشود، كه سبب كاهش استحكام سازه ميگردد. به منظور ارزيابي استحكام اينگونه سازه ها لازم است كه تنشهاي اطراف ترك يا شيار استخراج شده و رفتار شكست سازه در نوك ترك يا شيار به كمك مكانيك شكست بررسي گردد.
ABSTRACT
In many metallic structures, such as beehive beams, there are V-shaped grooves. Due to the concentration of intense tension around these grooves due to the shear load caused by bending in their neutral axis, and due to the behavior of the metal shapes, a plastic region is formed around these grooves, the shape and size of which have a significant impact on On the behavior of the failure of the structure and its dismay. In this paper, the plastic region for grooves with different angles in two stress and strain modes in pure shear loading (MODE II) has been investigated and an analytical relation has been presented for the dimensionless radius of the plastic region around the grooves. One of the important parameters in the study of the plastic region is the area of the plastic area and its size along the groove axis. The results show that the shape of the plastic region for the grooves is similar to that of the region for the cracks and for all the angles of the groove, the change of state from stress to the strain on the shape of the plastic region to the groove is not very effective, most of the plastic region behind the groove With the increase of the Poisson coefficient, the area of this area has been reduced to a very small extent. It is also observed that in Mode II loading, the increase in the Poisson’s coefficient does not change the radius of the plastic region along the groove axis.
INTRODUCTION
In metal structures, sometimes cracks and grooves during construction or due to existing defects are gradually created during the work of the structure due to applied loads. As an example in metal bridges due to the movement of vehicles, in thin shells used in pressure vessels due to low pressure, and the recall of pressure inside the reservoir, in electric motors due to wind flow, as well as in many other structures Engineering is caused by fatigue loads, cracks and grooves in the stress concentration areas, which reduces the strength of the structure. In order to evaluate the strength of such structures, it is necessary to investigate the stresses around the crack or groove and the failure behavior of the structure at the tip or groove with the help of failure mechanics.
Year: 2011
Publisher : Sixth National Congress on Civil Engineering
By : Majid Reza Ayatollahi, Hesamoddin Ghadiani
File Information: persian Language/ 8 Page / size: 412 KB
Only site members can download free of charge after registering and adding to the cart
سال : 1390
ناشر : ششمین کنـگره ملی مهنـدسی عمـران
کاری از : مجيد رضا آيت الهي ،حسام الدين قدياني
اطلاعات فایل : زبان فارسی / 8 صفحه / حجم : KB 412
نقد و بررسیها
هنوز بررسیای ثبت نشده است.