توضیحات
چکیده
در اين تحقيق، اثر ترك خوردن مكانيكي در سه شرايط مختلف بر ساختار انجماد آلاينده آلومينا آلفا 20-20٪ بررسي شده است. بررسی ساختارهای بمبگذاری مکانیکی نشان داد که افزایش سرعت پرشده، اندازه ذرات و نسبت طول به عرض را کاهش می دهد. زمان مطلوب برای تکان دادن مکانیکی 10 دقیقه است. همچنین ساختار نمونه های انعقاد در دمای 635 درجه سانتیگراد در همگن بودن نسبت به نمونه کشیده شده از بالای سطح مایع دارای یک نسبت تصویر است و در این نمونه ذرات سیلیکونی اولیه توزیع مناسب ندارند. همچنین تکان دادن مکانیکی از بالای سطح مایع به دمای نزدیک به انجماد باعث افزایش اندازه سیلیکون اولیه نسبت به حالت مرجع می شود.
مقدمه
آلیاژهای Al-Si Hyper-eutectic خواص خاصی از جمله مقاومت در برابر سایش، سختی و مقاومت بالا و ضریب ضریب انبساط حرارتی دارند که به طور گسترده ای در ساخت و ساز سیلندر و اجزای پمپ و قطب می شود. خواص معدنی این آلیاژ ها به میزان زیادی بر روی توزیع، اندازه و مورفولوژی ذرات سیلیکونی اولیه در این آلیاژ ها بستگی دارد. ذرات سیلیکون دارای مورفولوژی های مختلفی هستند، مانند یک صفحه، چند منظوره، ستاره ای شکل و شکل، که با شرایط یخ زدگی و ترکیب شیمیایی تغییر می کند. در ریخته گری های معمولی، تغییر ساختاری این آلیاژ ها با افزودن عناصر به سازنده انجام می شود. اگر چه عناصر اصلاح شیمیایی باعث بهبود مورفولوژی و توزیع اجزای میکرو سازنده می شوند، اما اثرات مضر نیز دارند. مطالعات نشان داده اند که این مواد ایجاد ترکیبات اضافی به نام “سخت” پوست، که خواص خواص مکانیکی این آلیاژ ها را کاهش می دهد، در حالی که برخی از این مواد اصلاح کننده سمی هستند و اثرات زیان آور محیط را دارند. به همین دلیل، روش های مختلفی برای ریخته گری نیمه جامد در بهبود ساختار این آلیاژ ها مورد توجه قرار گرفته است. در اين تحقيق اثر تشديد مکانیکی در شرايط مختلف و همچنين تأثير زمان و سرعت تشديد مکانیکی بر ريزساختار آلیاژ آلومينيوم 20٪است.
ABSTRACT
In this research, the effect of mechanical stirring in three different conditions on the structure of freezing of Al-20% Si alloy has been investigated. Investigating the structures of mechanical bumping showed that increasing the speed of bumping reduces the particle size and the ratio of length to width. The optimal time for mechanical stirring is 10 minutes. Also, the structures of coagulated samples at 635 ºC in homogeneity compared to the sample drawn from above the liquid level have an Aspect Ratio, and in these samples, the primary silicon particles do not have a proper distribution. Also, mechanical stirring from above the liquid level to near freezing temperature causes an increase in the size of the initial silicon relative to the reference state.
INTRODUCTION
Al-Si hyper-eutectic alloys have special properties such as wear resistance, hardness and high strength, and low coefficient of thermal expansion, which makes them widely used in cylinder construction and pump and pulley components. The mineral properties of these alloys depend to a large extent on the distribution, size and morphology of primary silicon particles in these alloys. Silicon particles have different morphologies, such as a plate, multifaceted, star-shaped and shaped, which changes with freezing conditions and chemical composition. In typical castings, the structural modification of these alloys is performed by adding the elements to the builder. Although chemical modification elements improve morphology and the distribution of microstructural components, they also have harmful effects. Studies have shown that these materials create additional compounds called “hard” peels that reduce the properties of the mechanical properties of these alloys, while some of these modifying agents are toxic and have deleterious effects on the environment. For this reason, various methods of semi-solid casting have been considered in improving the structure of these alloys. In this research, the effect of mechanical stirring in different conditions, as well as the effect of time and mechanical stirring speed on microstructure of Al-20% Si alloy has been investigated.
Year: 2007
Publisher : 11th National Congress of metallurgy of Iran
By : Mohammad Ghalam Baz, Reza Noori, Mohsen Azizi, Mohammad Shahmiri, Yousef Haj Karim Kharazi
File Information: persian Language/ 12 Page / size: 2.92 KB
سال : 1386
ناشر : يازدهمين كنگره ملي مهندسين متالورژی ايران
کاری از : محمد قلم باز ،رضا نوري ،محسن عزيزي ،محمد شاهميري ،يوسف حاج كريم خرازي
اطلاعات فایل : زبان فارسی / 12صفحه / حجم : KB 2.92
نقد و بررسیها
هنوز بررسیای ثبت نشده است.