توضیحات
ABSTRACT
This research has an objective to determine shear capacity of a reinforced concrete beam with different cross section types of lateral reinforcement. The specimens used in this research are made from a reinforced concrete beam with its dimension is 100 mm width times 150 mm height and f /c = 18 MPa. The beam has 2#2 tension reinforcement lie at the bottom of the beam, and 2#2 reinforcement lie at the upper side of the beam to maintain the position of shear reinforcement. Shear reinforcement provide by 4 mm steel reinforcement spaced every 150 mm 200 mm at the middle of the beam. This shear reinforcement area fulfill minimum limit ratio specified in ACI 318-08. The test results indicated that no significant differences for shear capacity from each types of shear reinforcement cross section. But open stirrups can be considered as a practical use in the construction field.
INTRODUCTION
Concrete is weak in tension, and the concrete beam will collapse if there are no proper reinforcement. The tensile stresses develop in beams due to axial tension, bending, shear, torsion, or a combination of these forces. The location of cracks in the concrete beam depends on the direction of principal stresses. For the combined action of normal stresses and shear stresses, maximum diagonal tension may occur at about a distance d from the face of the support . The distance d is measure from the extreme compression fiber to the centre of the longitudinal tension reinforcement. Flexural shear cracks are the most common type found in reinforced concrete beams. A flexural crack extends vertically into the beam; then the inclined crack forms, starting from the top of the beam when shear stresses develop in that region. In regions of high shear stresses, beams must be reinforced by stirrups or by bent bars to produce ductile beams that do not rupture at a failure. If shear reinforcement is not provided, brittle failure will occur without warning. To avoid brittle failure, ACI 318-08 Code requires that the minimum shear reinforcement area, Av = 0.35bws/fy for the compressive strength of concrete up to 31 MPa. For concrete with compressive strength more than 31 MPa, the ACI 318-08 Code specify minimum shear reinforcement area, Av = 0.0062 f /c (bws/fy).
چکیده
اين پژوهش با هدف تعيين ظرفيت برشي يک پرتو بتن مسلح با انواع مختلف مقطع تقويت جانبی انجام شده است. نمونه های مورد استفاده در این تحقیق از یک پرتو بتن مسلح ساخته شده اند که ابعاد آن 100 میلی متر عرض و 150 میلیمتر ارتفاع و F / c = 18 MPa است. پرتو دارای 2 # 2 تقویت کشش دروغ در پایین پرتو، و 2 # 2 تقویت دروغ در طرف بالا از پرتو برای حفظ موقعیت تقویت برش. تقویت برش توسط 4 میلیمتر تقویت فولادی توسط هر 150 میلیمتر 200 میلیمتر در وسط پرتو ارائه شده است. این منطقه تقویت برش حداقل مقدار محدودیت مشخص شده در ACI 318-08 را برآورده می کند. نتایج آزمون نشان داد که هیچ تفاوت معنیداری برای ظرفیت برشی در هر نوع صلیب تقویتی برش وجود ندارد. اما راهپیمای باز می تواند به عنوان یک کاربرد عملی در زمینه ساخت و ساز در نظر گرفته شود.
مقدمه
بتن در کشش ضعیف است و اگر بتن مسلح وجود نداشته باشد، بتن بتونی سقوط خواهد کرد. تنش کششی در پرتو ها به علت تنش محوری، خم شدن، برش، پیچش یا ترکیبی از این نیروها ایجاد می شود. محل ترک در پرتو بتن به جهت تنش های اصلی بستگی دارد. برای عمل ترکیبی تنش های عادی و تنش های برشی، حداکثر تنش مورب ممکن است در حدود d از چهره پشتیبانی رخ دهد. فاصله d از فیبر فشرده شدید به مرکز تقویت کشش طولی اندازه گیری می شود. ترکهای انعطاف پذیر انعطاف پذیر شایع ترین نوع در تیرهای بتن مسلح هستند. کرک خمشی عمود بر روی پرتو گسترش می یابد؛ سپس ترک شکاف ایجاد می شود، شروع از بالای پرتو زمانی که تنش برشی در آن منطقه توسعه می یابد. در مناطق تنش برشی بالا، پرتوها باید توسط استروپ ها یا میله های خمشی تقویت شوند تا پرتوهای مجذور را که در شکست ناپدید می شوند، تولید نکنند. اگر تقویت برشی ارائه نشود، شکست شکننده بدون هشدار رخ می دهد. برای جلوگیری از شکست شکننده، ACI 318-08 کد نیاز به حداقل منطقه تقویت برش، Av = 0.35bws / fy برای مقاومت فشاری بتن تا 31 مگاپاسکال است. برای بتن با استحکام فشاری بیش از 31 مگاپاسکال، کد ACI 318-08 حداقل سطح تقویت برش، Av = 0.0062 f / c (bws / fy) را مشخص می کند.
Year: 2012
Publisher : ELSEVIER
By : Agus Setiawan , Kiki Saptono
File Information: English Language/ 10 Page / size: 666 KB
Only site members can download free of charge after registering and adding to the cart
سال : 1391
ناشر : ELSEVIER
کاری از : Agus Setiawan، Kiki Saptono
اطلاعات فایل : زبان انگلیسی / 10 صفحه / حجم : KB 666
نقد و بررسیها
هنوز بررسیای ثبت نشده است.