توضیحات
ABSTRACT
The industrial requirements for the control of an induction machine without a mechanical sensor continue to be of interest, as evidenced by the most recent publications. The focus is on improvements of control without a mechanical sensor. A new method for the implementation of a sensorless indirect stator- fluxoriented control (ISFOC) of a single-phase induction motor (SPIM) drive is proposed in this paper. The proposed method of rotor speed estimation is based only on the measurement of the main and auxiliary windings stator currents and that of a reference q-axis current generated by the control algorithm. The error of the measured qaxis current from its reference value feeds the proportional plus integral controller, the output of which is the estimated slip angular frequency. Experimental results for sensorless ISFOC speed control of a SPIM drive are presented and analyzed using a dSPACE system with DS1104 controller board based on the digital signal processor TMS320F240. Digital simulation and experimental results are presented to show the improvement in performance of the proposed sensorless algorithm.
INTRODUCTION
SINGLE-PHASE induction motors (SPIM) are traditionally used in constant speed home appliances, usually in locations where only single-phase energy supply is available without any type of control strategy. They are found in air conditioners, washers, dryers, industrial machinery, fans, blowers, vacuum cleaners, and many other applications. Variable speed controls of electrical motors are widely employed in industrial applications because of the obvious energy-saving benefits. The cost reduction and high efficiency of power electronic and microelectronics devices are motivating to implement a SPIM drives in both industrial and domestic applications. During recent years, many research laboratories have focussed on variable-speed drives, especially for the SPIM, and major improvements have been achieved. The availability of low-cost static converters makes possible the economic use of energy and improvement of the quality of the electromagnetic torque in SPIM . They are three power electronic converter topologies of two-phase inverters for SPIM: two-leg, three-leg, and four-leg inverters. In recent years, the topology with three-leg two-phase with six-transistor bridge voltage source inverter for SPIM drive systems has been preferred by many researchers compared to the other topologies.
چکیده
نیازمندی های صنعتی برای کنترل یک ماشین القایی بدون یک سنسور مکانیکی همچنان مورد توجه است، که اخیرا در نشریات نشان داده شده است. تمرکز بر بهبود کنترل بدون یک سنسور مکانیکی است. در این مقاله یک روش جدید برای پیاده سازی یک کنترل مستقل سنسور غیر مستقیم (ISFOC) از یک موتور القایی تک فاز (SPIM) ارائه شده است. روش پیشنهادی برآورد سرعت روتور تنها بر اندازه گیری جریان استاتور جریان الکتریسیته ساکن اصلی و کمکی و جریان محوری q مرجع تولید شده توسط الگوریتم کنترل استوار است. خطای جریان qaxis اندازه گیری شده از مقدار مرجع آن، یک کنترل کننده انتگرال متناسب را فراهم می کند که خروجی آن فرکانس زاویه ای تخمین زده شده است. نتایج تجربی برای کنترل سرعت ISFOC حسگر درایو SPIM ارائه شده و با استفاده از یک سیستم dSPACE با کنترل کننده DS1104 بر اساس پردازنده سیگنال دیجیتال TMS320F240، تجزیه و تحلیل شد. شبیه سازی دیجیتال و نتایج تجربی برای نشان دادن بهبود عملکرد الگوریتم سنسور پیشنهاد شده ارائه شده است.
مقدمه
موتورهای القایی یکپارچه (SPIM) به طور سنتی در لوازم خانگی با سرعت ثابت استفاده می شود، معمولا در مکان هایی که تنها عرضه تک فاز بدون هیچ نوع استراتژی کنترل در دسترس است. آنها در تهویه مطبوع، واشر، خشک کن، ماشین آلات صنعتی، فن، دمنده، جاروبرقی و بسیاری از کاربردهای دیگر یافت می شوند. کنترل های متغیر سرعت موتورهای الکتریکی به علت مزایای صرفه جویی در صرفه جویی در انرژی در کاربردهای صنعتی به طور گسترده ای مورد استفاده قرار می گیرند. کاهش هزینه و بهره وری بالا دستگاه های الکترونیکی و میکرو الکترونیک قدرت انگیزه برای اجرای درایو SPIM در هر دو کاربرد صنعتی و داخلی است. در طول سال های اخیر، بسیاری از آزمایشگاه های تحقیقاتی بر روی درایوهای متغیر سرعت، مخصوصا برای SPIM تمرکز کرده اند و پیشرفت های عمده ای صورت گرفته است. در دسترس بودن مبدل های ارزان قیمت استاتیک امکان استفاده اقتصادی از انرژی و بهبود کیفیت گشتاور الکترومغناطیسی در SPIM را فراهم می آورد. این سه توپولوژی مبدل الکترونیک مبدل مبدل های دو فاز برای SPIM: دو تبدیل کننده، سه پایه و چهار پایه است. در سال های اخیر توپولوژی سه پایه دو فاز با اینورتر منبع ولتاژ پل شش ترانزیستور برای سیستم های درایو SPIM توسط بسیاری از محققان ترجیح داده شده است در مقایسه با توپولوژی های دیگر است.
Year: 2009
Publisher : IEEE
By : Mohamed Jemli, Hechmi Ben Azza, Mohamed Boussak, and Moncef Gossa
File Information: English Language/ 10 Page / size: 0.98 KB
Only site members can download free of charge after registering and adding to the cart
سال : 1388
ناشر : IEEE
کاری از : محمد جملی، حمی بن عذا، محمد بواسک و منسف گوسا
اطلاعات فایل : زبان انگلیسی / 10 صفحه / حجم : KB 0.98
نقد و بررسیها
هنوز بررسیای ثبت نشده است.