توضیحات
چکیده
آلیاژهاي سري 7xxxآلومينيم در هر موردي كه استحكام ويژه مطرح باشد به ويژه در صنایع هوا – فضا اهميت دارند.این مواد با توجه به چگالي كم، استحكام و تافنس بالاي خود سبب كاهش وزن سازه هـاي مذكور مي شوندكه از اهميت به سزايي برخوردار است. در اين پژوهش، رفتار آلياژهاي 7075و7050 استحكام بالاي آلومينيم درحضور مراكز تمركز تنش مقايسه و مكانيسم هـاي غالـب در گـسيختگي ايـن آلياژها بررسي شده است. براي اين منظور از نمونه هاي پارگي حاوي شيار -Vشكل با ابعـاد كوچـك و ضخامت 6/35ميليمتر استفاده شد. شعاع راس شـيار نمونـه هـا مطـابق بـا اسـتاندارد ASTM B871-96 كمتر از 60ميكرون مي باشد. جهت بررسي تأثير شعاع راس شيار بر نتايج آزمايش پارگي نمونه هـايي بـا شعاع راس شيار در حدود 20ميكرون نيز در نظرگرفته شد. مطـابق بـا ايـن اسـتاندارد، نـسبت اسـتحكام پارگي به تنش تسليم %0/2نمونه ها به عنوان معياري براي ارزيـابي تـافنس شيار منظـ رو مـي گـردد. بـا بررسي سطوح شكست مكانيسم هاي شكست تحليل شد. با توجه به ميكروگراف هاي سـطوح شكـست ، رسوب هاي حاصل از عمليات حرارتي پير سختي به عنوان محل هاي جوانه زني حفره ها و آغاز شكست نمونه ها مطرح مي باشد. مكانيسم هاي متفاوت جهت ايجاد و رشـد تـرك در نزديـك محـل شـيار و در ساير نقاط نمونه بررسي و بحث گرديد.
مقدمه
آلومينيم و آلياژهاي آن از زمره آلياژهاي بسيار مهم در صنعت محسوب مي شود كه داراي چگالي پـايين و استحكام ويژة بالا مي باشد. البته بيشترين ميزان استحكام به آلياژهاي گروه (Al-Zn-Mg) 7xxxتعلق دارد، كه افزايش استحكام در آنها توسط عمليات حرارتي پير سختي حاصل مي شـو.د بيـشترين كـاربرد اين گروه از آلياژ هاي آلومينيم درصنايع حمـل و نقـل هـوايي و هوانـوردي اسـت. شـايد آلياژهـاي 7050 ، 7075و 7055شناخته شده ترين و پرمصرف ترين آلياژهاي اين گروه باشند. از آنجايي كـه حساسيت به شيار اين آلياژ ها سبب افت خواص مكانيكي و محدوديت كاربرد مي شود، در اين پـژوهش رفتار مكانيكي آلياژهاي 7075و 7050استحكام بـالاي آلـومينيم درحـضور مراكـز تمركـز تـنش مقايـسه و مكانيسم هاي غالب در گسيختگي اين آلياژها بررسي شده است.
ABSTRACT
Aluminum 7xxx series alloys are important in any case with special strength, especially in the aerospace industry. Due to their low density, strength and high toughness, these materials reduce the weight of the structures, which is of great importance. In this research, the behavior of alloys 7075 and 7050 with high strength of aluminum in the presence of stress concentration centers and the dominant mechanisms in the failure of these alloys have been investigated. To this end, tear-off teeth containing a V-shaped groove with a small dimension and a thickness of 35.6 mm were used. The peak radius of the sample grooves is below 60 microns in accordance with ASTM B871-96 standard. To investigate the effect of the radial radius on the results of the rupture test, samples with a groove radius of about 20 microns were considered. In accordance with this standard, the tear strength ratio to the yield stress of 0.2% of the samples is considered as a benchmark for evaluation of the groove’s tofence. Analyzing the failure levels of failure mechanisms was analyzed. According to the micrographs of the fracture surfaces, the precipitates from the hard heat treatment are considered as germination points of the cavities and the beginning of failure of the samples. Different mechanisms for creating and growing cracks near the groove site and in other points of the sample were discussed.
INTRODUCTION
Aluminum and its alloys are among the most important alloys in the industry, which have low density and high specific strength. Of course, the highest level of strength belongs to alloys of the group (Al-Zn-Mg) 7xxx, which increase their strength in them by thermal hardening of hardness. The most common use of this group is aluminum alloys in the field of air transport and aviation. Perhaps the 7050, 7075 and 7055 alloys are the most well known and most widely used alloys in this group. Since the sensitivity to the slab of these alloys causes mechanical properties and application limitation, in this research, the mechanical behavior of 7075 and 7050 high strength aluminum alloys in the presence of stress concentration centers and the dominant mechanisms in the failure of these alloys have been investigated.
Year: 2007
Publisher : 11th National Congress of metallurgy of Iran
By : Kazempour Azarang, Parvin Abachi, Parviz Pourkar Nasoidi, Pooyan Shoshtari Zadeh Naseri
File Information: persian Language/ 15 Page / size: 1.30 KB
سال : 1386
ناشر : يازدهمين كنگره ملي مهندسين متالورژی ايران
کاری از : كاظم پور آذرنگ ، پروين عباچي ،پرويز پوركار نسودي ، پويان شوشتري زاده ناصري
اطلاعات فایل : زبان فارسی / 15 صفحه / حجم : KB 1.30
نقد و بررسیها
هنوز بررسیای ثبت نشده است.