توضیحات
چکیده
با توجه به اينكه جوش ها به عنوان يكي از مهمترين اتصال دهنده ها از حساس ترين قسمت هاي باربري در اتصالات سازه هاي فولادي هستند، بررسي رفتار و مقاومت آنها در سازه ها امري الزامي مي باشد. در مقااله پيش رو با استفاده از نرم افزار اجزاي محدود و به روش تحليل غير خطي ستاتيكي به بررسي رفتار جوش هاي گوشه، نيم جناغي يك طرفه و نيم جناغي دو طرفه از نقطه نظر مقاومت، شكل پذيري و تاثير باربري نها بر سطح عملكرد قاب هاي خمشي فولادي پرداخته شده است.گسيختگي در جوش نيم جناغي يك طرفه هميشه با شروع ترك از ريشه جوش آغاز مي شود كه حالت نامطلوبي در گسيختگي محسوب مي شود. مشكل جوش گوشه نيز خارج از اندازه بودن بعضي نقاط آن در طول خط جوش است، كه كنترل آن مشكل مي باشد و گسيختگي از همان نقاط آغاز مي گردد. در نهايت باتوجه به نتايج بدست آمده، بهترين رفتار در جوش نيم جناغي دو طرفه ملاحظه گرديده است.
مقدمه
قابهاي خمشي اغلب در ساختمان هاي كوتاه مرتبه و ميان مرتبه استفاده مي گردند. اين سيستم ها به تنهايي و يا به صورت تركيب با سيستم هاي ديگر وظيفه باربري جانبي را به عهده دارند. با توجه به شكست هاي ترد به وجود آمده در اتصالات جوشي تير به ستون در زلزله نورتريج ،( 1994آمريكا) و هنگ كنگ ،1995تحقيقات گسترده اي بر روي انواع اتصالات جوشي انجام و علت رفتار نامناسب هاآن مورد بررسي قرار گرفته است .بر اساس اين تحقيقات، علت هاي اصلي شكست دراتصالات جوشي عبارتند از: – عدم جوشكاري مناسب (نفوذ ناقص فلز جوش، وجود ترك ر ريشه جوش )…و – اجراي نامناسب اتصالات(ايجاد تمركز تنش رد ريشه جوش) – استفاده ازالكترود نامناسب تحقيقات انجام گرفته در آمريكا ژاپن با هدف بهبود عملكرد لرزهاي اتصالات جوشي در قاب هاي خمشي فولادي، نشان ميدهدكه روش جوشكاري GMAW(جوش قوس الكتريكي تحت حفاظت گاز) عليرغم هزينه بيشتر، چقرمگي بيشتري را نسبت به روش ( FACWجوش قوس الكتريكي با الكترود توپودري) ايجاد ميکند. در تحقيقي ديگر استراتان و دوبينا روي پنجاه و چهار نمونه اتصال تي شكل، رفتار انواع جوش گوشه، نيم جناغي يك طرفه و نيم جناغي دوطرفه را تحت بارگذاري يكنواخت و چرخه ،اي مورد بررسي قرار داده و نتيجه گيري كردند كه كيفيت جوشكاري مهمترين پارامتر درعملكرد اتصالات جوشي مي باشد. همچنين از ميان نمونه هاي مورد بررسي، بهترين رفتار در جوش درز نيم جناغي دوطرفه اعلام گرديد.
ABSTRACT
Due to the fact that the welds are one of the most important fasteners of the most sensitive portions of the steel structure joints, their behavior and resistance testing in structures is necessary. In the foregoing article, using finite element software and nonlinear static analysis method, the behavior of one-way, half-double-sided, semi-hexagonal, semi-double-sided, one-way and half-duplex beams, from the point of view of strength, ductility and the effect of their load on the performance of the frames The bending of the steel has been dealt with. The dislocation of a one-way hemisphere always begins with the onset of cracking from the welding root, which is considered to be a disadvantage in failure. The buckling problem is also outside the size of some of its points along the weld line, which is difficult to control, and the failure begins at the same points. Finally, with regard to the results, the best behavior in bilateral hemicondia was observed.
INTRODUCTION
Bending frames are often used in short and intermediate-sized buildings. These systems, alone or in combination with other systems, carry out side loading tasks. Due to the brittleness of the jig-to-column couplings in the Northbridge earthquake (1994 America) and Hong Kong, 1995, extensive research has been carried out on the types of welding joints and the cause of inappropriate behavior has been studied. Based on these studies The main causes of failure in welding joints are: – lack of proper welding (incomplete penetration of the weld metal, the presence of cracked root cavity), and – inadequate fitting of joints (the creation of stress concentration of the root of the weld), – the use of inappropriate electrode research carried out in The United States of America, Japan, aims to improve the seismic performance of welding joints in steel flexural frames, indicating that the welding method GMAW (Swirling Sword Electric gas protected by gas), despite the higher cost, creates more toughness than the method (FACW electric arc welding with electrode electrode). In another study, the Stearns and Dubna on fifty-four T-shaped T-shaped samples examined the behavior of a single-sided, semi-double-sided, double-sided, double-sided, semi-double-sided behavior under uniform loading and cycling, and concluded that the welding quality was the most important parameter in operation Welding connections. Also, among the studied samples, the best behavior was reported in bilateral semicircular joints.
Year: 2011
Publisher : Sixth National Congress on Civil Engineering
By : Jafar Asgari Marnani, Maryam Yazdani and Negar Sorkh Lion
File Information: persian Language/ 8 Page / size: 1,39 KB
Only site members can download free of charge after registering and adding to the cart
سال : 1390
ناشر : ششمین کنـگره ملی مهنـدسی عمـران
کاری از : جعفر عسگري مارناني ،مريم يزداني و نگارقره شير
اطلاعات فایل : زبان فارسی / 8 صفحه / حجم : KB 1,39
نقد و بررسیها
هنوز بررسیای ثبت نشده است.