توضیحات
چکیده
فرايند متداول براي ساخت كامپوزيت تنگستن- مس، آسياكاري مكانيكي وسپس تف جوشي مخلوط پودري ميباشد. يكي از مشكلات عملي مهم كه در حين آسياكاري اتفاق ميافتد تمايل زياد پودر به چسبيدن به ابزار آسيا كاري ميباشد. (ديواره ظرف وگلوله ها ) اين چسبيدن باعث كاهش بازدهي آسيا ميشود. يكي از روشهايي كه براي كاهش چسبيدگي پودر بكار ميرود، ك اضافه ردن عامل كنترل كننده فرآيند ميباشد. در اين مقاله اثر هگزان و اسيد استئاريك به عنوان عامل كنترلكننده فرآيند بر اندازه ذرات تحقيق شده است. مورفولوژي پودر آسيا شده بوسيله ميكروسكوپ الكتروني روبشي و محاسبات اندازه دانه با استفاده از الگوهاي پراش اشعه ايكس، بررسي شده است. نتايج تحقيق نشان ميدهد كه استفاده از عامل كنترلكننده فرآيند به صورت مؤثري باعث كاهش اندازه نهايي ذرات پودرآسيا شده ميگردد. استفاده از آسياكاري تر با استفاده از هگزان باعث كاهش زمان تشكيل نانوكامپوزيت به10 ساعت ميگردد.
مقدمه
نانوكامپوزيت هاي تنگستن-مس از ذرات پراكنده تنگستن در يك زمينه مس تشكيل شده اند. گستردگي كاربرد اين نانوكامپوزيت بدليل خواص منحصر بفرد آن است كه بدليل هدايت الكتريكي وگرمايي بالاي مس و ضريب انبساط كوچك تنگستن مي باشد. موارد استفاده اين نانوكامپوزيت به صورت گسترده در صنايع الكترونيك، الكترودهاي جوشكاري و وسايل هدايت گرمايي مي باشد. سيستم تنگستن-مس هيچگونه حلاليت دوطرفه نداشته و اختلاف زيادي در دماي ذوب و وزن مخصوصشان وجود دارد. به همين دليل ساخت اين كامپوزيت با روشهاي متداول ذوب و ريخته ري ممكن نيست و روش آسياكاري مكانيكي جايگزين بسيار مناسبي براي ساخت اين كامپوزيت ميباشد. اساس كار آسياكاري مكانيكي بر پايه جوش خوردگي و شكست مداوم ذرات پودر در اثر نيروهاي برشي وارده به وسيله گلوله ها و تكرار اين فرآيند مي باشد. توده كامپوزيتي اوليه در اثر اضافه شدن ذرات فاز سخت تر به فاز نرمتر در مراحل اوليه آسيا كاري شكل ميگيرد. اندازه اين توده اوليه ممكن است بسيار بزرگتر از اندازه ذرات پودر هاي اوليه باشد. در مراحل بعدي اندازه توده كامپوزيتي در اثر كار سختي مرتبا كاهش مي يابد. يكي از مشكلات مهمي كه در حين آسيا ا كاري مكانيكي اتفاق مي فتد، چسبيدن پودر به ابزار آسياكاري و ديواره ظرف است.
ABSTRACT
A common process for making tungsten-copper composites, mechanical asymmetric and then sputtering powder mixtures. One of the most important practical problems that occurs during an asynchronous operation is the high tendency of the powder to adhere to the Asiatic tool. (Duct walls and bulbs) This sticking reduces the efficiency of the Asia. One of the methods used to reduce the adhesion of the powder is the addition of process control agent. In this paper, the effect of hexane and stearic acid as process control agent on particle size has been investigated. The morphology of ASA powder was studied by scanning electron microscopy and grain size calculations using X-ray diffraction patterns. The results of the study show that the use of process control agent effectively reduces the final size of powdered particles. The use of hexane as a greaser reduces the time of nanocomposite formation to 10 hours.
INTRODUCTION
Tungsten-copper nanocomposites consist of tungsten dispersed particles in a copper field. The application of this nanocomposite is due to its unique properties due to high electrical conductivity and high copper and a small expansion coefficient of tungsten. Uses of this nanocomposite are widely used in electronic industry, welding electrodes and thermal conductivity devices. Tungsten-copper system has no two-way solubility and there is a great difference in the melting temperature and their specific weight. For this reason, it is not possible to fabricate this composite with conventional melting and casting techniques, and the mechanical asyactic method is an excellent alternative to making this composite. The basis of the mechanical asynchronous machining is based on the welding and continuous failure of powder particles due to the shear forces of the bullets and the repetition of this process. The primary composite mass is formed by the addition of more difficult phase particles to a more softened phase in the early stages of the asynchronous work. The size of this primary mass may be much larger than the size of the particles of the primary powder. In later stages, the composite mass size decreases steadily through hard work. One of the major problems that occurs during Asia is to adhere the powder to the tool and the wall of the container.
Year: 2007
Publisher : 11th National Congress of metallurgy of Iran
By : Siamak Ehnehi, Nader Parvin, Azadeh Motaleh, Maryam Salehi, Mohsen Afrasibi
File Information: persian Language/ 10 Page / size: 1,86 KB
سال : 1386
ناشر : يازدهمين كنگره ملي مهندسين متالورژی ايران
کاری از : سيامك اقتصادي ،نادر پروين ،آزاده متأله ،مريم صالحي ،محسن افراسيابي
اطلاعات فایل : زبان فارسی / 10 صفحه / حجم : KB 1,86
نقد و بررسیها
هنوز بررسیای ثبت نشده است.