توضیحات
چکیده
نقش آسيا كاري مكانيكي بر روي خواص حرارتي و مورفولوژي پلي اتيلن دانسيته متوسط (MDPE) با بررسي دو پارامتر اصلي آسيا كاري يعني تغييرزمان آسياكاري و نسبت وزن گلوله به پودر (نسبت شارژ) ، بررسي گرديده است.پلي اتيلن بصورت پودر با ابعاد ،100 µmدر زمان هاي متغير 5تا 20ساعت و نسبت هاي شارژ 10تا 30و در دماي محيط مورد آسيا قرار گرفت . بررسي تغييرات ريز ساختار توسط ميكروسكوپ الكترونيكي روبشي (SEM) در بزرگنمايي هاي متفاوت نشان از تغييرات عمده در ريز ساختار با افزايش زمان آسيا كاري در نسبت شارژ ثابت و همچنين با افزايش نسبت شارژ در زمان ثابت دارد . خواص حرارتي نمونه هاي فوق توسط دستگاه آناليز كالريمتري (DSC) بررسي شد . نتايج ، كاهش نسبي دماي بلورينگي را با افزايش زمان آسياكاري و همچنين نسبت شارژ نشان مي دهد . همچنين درصد بلورينگي كه متناسب با تغييرات آنتالپي است ، با افزايش زمان آسيا كاري مكانيكي كاهش پيدا كرده است اما با افزايش نسبت شارژ ، درصد بلورينگي در زمان ثابت روند صعودي داشته است . دماي ذوب با افزايش زمان آسياكاري و تغييرات نسبت شارژ تغيير نمي كند .
مقدمه
آسياكاري مكانيكي (تك جزء) وياآلياژسازي مكانيكي (دو ويا چند جزء)در اواخر سال 1960وبراي آلياژسازي فلزات مورد استفاده قرار گرفت. آسيا كاري پليمرهانيز با پوشش دهي پودرهاي فلزي توسط پليمر مورد استفاده واقع شد ، اما به تدريج آسياكاري پليمر ها جهت آلياژسازي پليمرهاي غير قابل حل در يكديگرمتداول گرديد .اين روش از آنجايي كه در حالت جامد صورت مي گيرد نسبت به روشهاي ديگر مخلوط سازي مانند ذوب و محلول سازي كه بخاطر ايجاد جريان گرمايي بالاي منجر به ذوب و يا عدم توانايي در جداسازي ناشي از محلول سازي، همواره با مشكلاتي مواجه بوده است داراي برتري هاي نسبي مي باشد. ميزان تاثير آسياكاري بر خواص پليمرها بستگي مستقيم به انرژي آسياكاري داردكه اين انرژي از پارامترهاي آسياكاري شامل نسبت وزني گلوله به پودر(نسبت شارژ)،دماي آسيا،زمان آسياكاري،طراحي آسيا و نسبت قطر گلوله ها به قطر داخلي ظرف تحت تاثير مي باشد. تغييرات خواص بوجود آمده بر روي پليمرها بعد از آسيا كاري مكانيكي همواره مورد توجه محققان بوده است.
ABSTRACT
The role of asynchronous mechanical work on the thermal properties and modulus density polyethylene morphology (MDPE) was investigated by examining two major Asian parameters, namely, the change in ASC and the ratio of the weight of the bullet to powder (charging ratio). Polyethylene in powder size of 100 μm at variable times of 5 to 20 hours and charge ratios of 10 to 30 at ambient temperature in Asia. Investigation of microstructure changes by scanning electron microscopy (SEM) in different magnifications shows the major changes in microstructure with increasing the time of operation in constant charge ratios and also with increasing charge retention in fixed time. The thermal properties of the samples were studied by calorimetry analyzer (DSC). The results show a relative decrease in the temperature of crystallinity with increasing asynchronous time and charge ratio. Also, the percentage of crystallinity that is proportional to the enthalpy variations has decreased with increasing mechanical time, but with increasing charge ratios, the percentage of crystallinity has risen steadily over time. The melting temperature does not change with the increase in asynchronous time and changes in charge ratio.
INTRODUCTION
Mechanical asynamics (single component) or mechanical alloys (two or more components) were used in the late 1960s for metal alloys. Polymer coating was used to coat metal powder by polymer, but gradually asymmetric polymer was used for alloying of insoluble polymers. This method, as it is in solid state, is more suitable than other methods of mixing such as melting And solubility that has always been difficult to produce due to high thermal conductivity or melting or inability to separate from solubilization, has relative advantages. The effect of asyncuria on the properties of polymers depends directly on the asymmetric energy, which is affected by ASI parameters, including the ratio of weight to bulb (charge ratio), Asian temperature, ASI time, Asian design, and the diameter ratio of the pellets to the inner diameter of the container. Changes in the properties of the polymers after the mechanical work have always been of interest to the researchers.
Year: 2007
Publisher : 11th National Congress of metallurgy of Iran
By : Mohammad Norouzi-Seyyed Mojtaba Zebrajd
File Information: persian Language/ 12 Page / size: 3.21 KB
سال : 1386
ناشر : يازدهمين كنگره ملي مهندسين متالورژی ايران
کاری از : محمد نوروزي-سيد مجتبي زبرجد
اطلاعات فایل : زبان فارسی / 12 صفحه / حجم : KB 3.21
نقد و بررسیها
هنوز بررسیای ثبت نشده است.