توضیحات
چکیده
در این پژوهش ريزساختار و تاثير حضور Niبر رفتار سايشي پوشش از WC-Niاعمال شده بر سطح فولاد ساده كربني مورد بررسي قرار گرفته است. بدين منظور مخلوط پودر مناسبي از عناصر خالص W-C-Niتهيه شده و بر سطح فولاد ساده كربني با ضخامت حدود 2ميليمتر اعمـال شـد و سـپس اين لايه از پيش نشانده شده توسط روش GTAWذوب شده تـا بـا فلـز پايـه امتـزاج يابـد. سـپس نمونه های رویه سختي شده تحت آزمـون هـاي مختلـف متـالوگرافي نـوري ، میكروسـكوپ الكترونـي رویشی, میكروسختي سنجي و سايش قرار گرفته اند. نتایج بررسي هاي به عمل آمده نشان مـيدهنـد كه تشكيل كاربيدهاي يوتكتيك نواري و گلي شكل حین انجمـاد مهمتـرين عامـل در بهبـود رفتـار سایشی پوشش مذكور ميباشند. همچنين بررسي ها نشان اد این لايـه پوششـي داراي سـختي بـالا (950-1200HV) و ضریب اصطكاك پايين (15/0)بوده كه به طور قابل ملاحظـه يا سـبب بهبـود مقاومت سایشي و كاهش ضريب اصطكاك نمونه های فولاد میگردد.
مقدمه
امروزه به منظور بهبود رفتار سطحي، برحسب نوع كاربرد و شرايط طيف وسـيعي از تكنيـك هـاي بهبودسازي سطح به كار گرفته مي شوند: عمليات سطحي با ليزر، پرتوالكترون، پاشش هـاي نفـوذي، رويه سختي و …. كه در اين ميان عمليات رويه سختي در مقايسه با ساير تكنيك ها بدلايلي از جمله: هزينه هاي نسبتاً پايين اجرا، قابليت پرتابل بودن فرايند و تنوع كاربرد بيشتر مدنظر قرار گرفته اسـت. رويه سختي عبارت است از ايجاد يك لايه فلزي يا بين فلزي از تركيبات سختي چون كاربيدها بر روي سطح فلز توسط جوشكاري (SMAW2, GTAW1و اكسي اتيلن)، پاشش (Plasma Spray, HVOF3) يا ساير روش هاي پاشش حرارتي كه البته در مقايسه با روش هاي پاشش حرارتي نظير ،HVOF روش جوشكاري تنگستن-گاز ،(GTAW) هزينه تمام شـده پـايين تـري داشـته و بـه عـلاوه تشـكيل تخلخل ها و تركيبات اكسيدي كمتري را به دليل استفاده از گاز محافظ آرگون ميتوان انتظار داشـت. در اين تكنيك، امتزاج و نفوذ پوشش و فلز پايه در محل فصل مشترك اتصال بسـيار محكمـي را پديد ميآورد. ضخامت لايه اعمالي بسته به نوع كاربرد در گستره يك تا چند ميليمتر است. بـه طـور كلي در اين تكنيك انتخاب صحيح پوشش و شرايط مناسب جوشكاري شرايط اصلي در موفقيت كـار هستند.
ABSTRACT
In this research, the microstructure and the effect of Ni presence on the wear behavior of WC-Ni applied on the surface of carbon steel have been investigated. For this purpose, a suitable powder mixture was prepared from pure W-C-Ni elements and applied on a surface of carbon steel of about 2 mm thick, and then melted to the base metal by the pre-set GTAW method. Then, hardened hardening samples were subjected to various light metalography, microscopic, microscopic, and abrasive tests. The results of the investigations show that the formation of strip and eutectic carbides during freezing are the most important factors in improving the abrasion behavior of the coating. Also, the studies show this high hardness layer (1200-950 Hz) and low friction coefficient (0.15) which significantly improves wear resistance and decreases the coefficient of friction of steel samples.
INTRODUCTION
Today, in order to improve surface behavior, surface tuning techniques such as laser, ultraviolet, penetrating, hardening, etc. are used, depending on the type of application and the wide range of conditions. Among these, the hardening procedure In comparison with other techniques, there are some problems such as relatively low running costs, portability of the process, and greater variety of applications. The hardening process consists of creating a metal or interlayer layer of hard materials such as carbides on the surface of the metal by welding (SMAW2, GTAW1 and oxyethylene), spraying (Plasma Spray, HVOF3) or other thermal spraying methods, which, in contrast to the method Heat spraying, such as HVOF, Tungsten-Gas-welding (GTAW), has lower finished costs and, moreover, the formation of porosity and lower oxidation can be expected due to the use of argon-protective gas. In this technique, the mixing and penetration of the base and metal coatings at the joint site creates a very strong connection. The thickness of the applied layer varies from one to several millimeters depending on the application. Generally, in this technique, the right choice of coating and suitable welding conditions are the main prerequisites for the success of the work.
Year: 2007
Publisher : 11th National Congress of metallurgy of Iran
By : Reza Amini and Morteza Shamanian
File Information: persian Language/ 10 Page / size: 1.74 KB
سال : 1386
ناشر : يازدهمين كنگره ملي مهندسين متالورژی ايران
کاری از : رضا اميني و مرتضي شمعانيان
اطلاعات فایل : زبان فارسی / 10صفحه / حجم : KB 1.74
نقد و بررسیها
هنوز بررسیای ثبت نشده است.