توضیحات
چکیده
با توجه به حضور درصدهاي متفاوت گاز سولفيد هيدروژن در منابع گـازي كـشور و خـسارات ناشـي از حضور اين گاز و ترجيح استفاده از لوله هاي فولادي معمولي بـه جـاي اسـتفاده از لولـه هـاي مخـصوص انتقال گاز ترش به دلايـل اقتـصادي، مطالعـه بـر روي پوشـش هاي مقـاوم در برابـر گـاز تـرش و اعمـال بـر فولادهاي معمولي امري ضـروري مـيباشـد.هـدف از ايـن تحقيـق بررسـي رفتـار خـوردگي و مكـانيكي پوششهاي اپوكسي پودري در محيط گاز ترش ميباشد.نمونه ها پس از قرار گـرفتن در محيط هـاي داراي گاز ترش ، تحت انجام آزمون هاي خوردگي HICو EISو همچنين آزمون هـاي مكـانيكي پوشـش شـامل چسبندگي، خمش و سايش قرار گرفتند.آناليز و بررسي نتايج نشان دهنـده خنثـي بـودن پوشـش FBEدر محيط گاز ترش و مقاومت به خـوردگي مناسـب ايـن مـاده پوشـشي و حفـظ خـواص مكـانيكي پوشـش خصوصا چسبندگي بعد از قرار گيري در محيط گاز تـرش اسـت.همچنـين نتـايج آزمـون خمـش بيـانگر ضرورت انتخاب ضخامت مناسب لايه پوششي با توجه به ترد بودن ذاتي پوشش هاي اپوكسي ميباشد.
مقدمه
در طي چند دهه اخير پيشرفت هاي زيادي در حوزه كنترل خوردگي و روش هاي پوشش دهي حاصـل شـده است و تحقيقات بر روي مـواد پليمـري بعنـوان يـك پوشـش مناسـب در جريـان مـيباشـد. در ايـن بـين پوشش هاي پليمري بر پايه اُلفين، وينيـل يـا پلميرهـاي پايـه اپوكـسي مـورد توجـه قـرار گرفتـه اسـت. پوشش هاي اپوكسي از رزين هايي با وزن مولكولي نسبتاً كم تشكيل ميشـود كـه در آن گـروه اپوكـسي در انتهاي هر مولكول قرار دارد اين رزين ها بـه همـرا سـخت كننـده هـا ، پيونـد عرضـي تـشكيل داده و يـك ساختمان گرماسخت ايجاد ميكند با افزايش وزن مولكولي رزين اپوكـسي ، مقاومـت شـيميايي افـزايش ولي خواصي همچون انعطاف پذيري كاهش مي يابد. اگرچه به خاطر كمبود اطلاعات در مورد رفتار اين پوشـش هـا در محـيط هـاي گـاز تـرش (H2S) امكـان استفاده آنها در سيستم هاي انتقال گاز ترش در كشور كاملاً بهره برداري نشده است. لوله هاي فولادي كه براي انتقال نفت و گاز مورد استفاده قرار ميگيرند مطابق با استاندارد نفت و گاز امريكـا داراي مشخـصه API-5L-Xميباشـند كـه مهتمـرين وجـه تمـايز آنهـا در ميكـرو سـاختار و تركيـب شـيميايي و خـواص مكانيكي ناشي از روش توليد ميباشد.
ABSTRACT
Considering the presence of different volumes of hydrogen sulfide gas in the country’s gas resources and the damage caused by the presence of this gas and the preference of using ordinary steel pipes instead of using special tubes for sour gas for economic reasons, study on resistant coatings Sour gas and applied to ordinary steels are essential. The purpose of this study was to investigate the corrosion and mechanical behavior of powdered epoxy coatings in sour gas. The samples were subjected to HIC and EIS corrosion tests after being exposed to sour gas. Mechanical cover tests included Bonding, bending and abrasion. The analysis and the results of the results show that the FBE coating is neutralized in the sour gas environment and the corrosion resistance of this coating material and the mechanical properties of the coating, especially adhesion after being placed in the sour gas, is maintained. Also, the results of bending test It is necessary to select the appropriate thickness of the coating layer due to the inherent crispness of the epoxy coatings.
INTRODUCTION
Over the past few decades, many advances have been made in the field of corrosion control and coating methods, and research on polymer materials is a good cover. At the same time, polymeric coatings based on olefin, vinyl or epoxy base pliers have been considered. Epoxy coatings consist of relatively low molecular weight resins in which the epoxy group is located at the end of each molecule. These resins, together with the hardening agents, form a transverse bond and create a thermosetting structure by increasing the molecular weight of the epoxy resin, The chemical resistance is increased, but properties such as flexibility are reduced. However, due to the lack of information on the behavior of these coatings in sour gas (H2S) environments, their use in sour gas transmission systems in the country has not been fully utilized. Steel tubes used for oil and gas transmission are API-5L-X according to the US Oil and Gas Standard, which distinguishes them from the microstructure, chemical composition and mechanical properties of the production method.
Year: 2007
Publisher : 11th National Congress of metallurgy of Iran
By : Reza Rouhi, Yousef Haj Karim Kharrazi, Alireza Khavandi, Mohammad Reza Bayati
File Information: persian Language/ 10 Page / size: 260 KB
سال : 1386
ناشر : يازدهمين كنگره ملي مهندسين متالورژی ايران
کاری از : رضا روحي ، يوسف حاج كريم خرازي ، عليرضا خاوندي ، محمدرضا بياتي
اطلاعات فایل : زبان فارسی / 10صفحه / حجم : KB 260
نقد و بررسیها
هنوز بررسیای ثبت نشده است.