توضیحات
چکیده
براي حذف آستنيت باقيمانده از برخي از انواع فولادهاي ابزارتحت شرایطي میتوان از عمليات تکميلي سردکردن زير صفر استفاده کرد. فـاز نيمـه پايـدار آسـتنيت از طرفـي مقاومـت بـه سـايش را کاهش داده و از طرفي ديگر با تبديل شدن به مارتنزيت باعـث تغييـر ابعـاد ناخواسـته مـي شـود و در نتيجه دقت ابعادي كاهش مي يابد. اين عمليات در مورد فولادهايي كه نياز به دقت ابعادي بالا و يـا مقاومت به سايش بالايي دارند به نحو وسيعي بکار مي رود. در اين تحقيق تاثير يپا دار شدن آسـتنيت يباق مانده در عمليات سرد كردن زير صفر تا دماي -63° Cو -180 ° Cبررسي شـد. نتـايج بدسـت آمده نشان داد که ي پا دار شدن آستنيت باقيمانده در عمليات زيـر صـفر باعـث بهبـود رفتـار سایشي و خواص مکانیکي فولاد مورد مطالعه مي شود.
مقدمه
براي حذف آستنيت باقيمانده از برخي از انواع فولادهاي ابزار امروزه از عمليات تکميلي سردکردن زير صفر استفاده وسيعي مي شود. آستنيت با قيمانده به عنوان يک فاز ضـعيف در کـاهش عمـر قطعـه نقـش بسزايي دارد. از سويي مارتنزيت باز پخت شده در عمل بسيار پذيرفته تر از آستنيت باقيمانـده اسـت زيـرا آستنيت باقيمانده با تبديل شدن به مارتنزيت تغيير ابعادي ناخواسته در قطعه پديد مي آورد، به همين دليل عمليات رد کردن زير صفر(کرايو) در مورد فولادهايي كه نياز به دقت ابعادي و يا مقاومت به سـايش بالايي دارند به شکل وسيعي بکار مي رود. دراين فرايند، بعد از عمليات کوئنچ, قطعـه را در شـرايط کنترل شده و با نرخ سرد کردن مناسب تا دماي مورد نظر سرد مي کنند. اگر اين فرآيند تا دماي نزديـک به -100° Cصورت گيرد به آن سرد کردن کرايو سطحي 2SCTو اگر تا دماي -180° Cصـورت گيرد به آن سرد کردن اکر يو عميق 3DCTمي گويند. در حالت کرايو سطحي درصـد قابـل توجـه و يـا تمام آستنيت باقيمانده از قطعه حذف مي شود و رفتار سايشي ماده به طور قابل توجهي بهبود مي يابـد در حالت سرد کردن عميق و سطحي بين درصد آستنيت باقيمانـده تفـاوتي وجـود نـدارد امـا در حالـت دوم بدليل ايجاد محل هاي جوانه زني کاربيد، درصد کاربيد افزايش يافتـه و پخـش يکنواخـت تـري از خـود نشان مي دهد.
ABSTRACT
In order to remove the remaining austenite from some types of steel, the use of a sub-zero cooling function can be used. The austenite semi-stable phase, on the other hand, reduces the wear resistance and on the other hand, by turning to martensite, it causes unwanted dimensional changes, and hence the dimensional accuracy decreases. This operation is widely used in the case of steels requiring high dimensional precision or high abrasion resistance. In this research, the effect of abrasion resistance of austenite was investigated in a cooling operation of below zero to -63 ° C and -180 ° C. The results showed that the residual austenite in the sub-zero operation improves the wear behavior and mechanical properties of the studied steel.
INTRODUCTION
To remove the remaining austenite from some types of steel, today, the use of a sub-zero cooling operation is widely used. Austenitic degradation plays a significant role in decreasing the life of a piece as a weak phase. On the other hand, open-cooking martensite is in practice much more acceptable than austenite, because the residual austenite, when converted to martensite, produces an unwanted dimensional change in the segment, which is why the operation of substituting zero (creeping) in the case of steels requiring precision Dimensional or high abrasion resistance are widely used. In this process, after the quench operation, the piece is cooled under controlled conditions and cooled down to the desired temperature. If this process reaches temperatures close to -100 ° C, it will cool down the 2SCT surface creep and, if heated to -180 ° C, it will cool down the 3DCT deep effect. In cryo-surface, a significant percentage or all remaining austenite is removed from the piece and the wear behavior of the material is significantly improved. In the deep and superficial cooling mode, there is no difference between the percentage of residual austenite, but in the latter case, due to the creation of sites Carbide germination shows a higher percentage of carbide and more uniform distribution.
Year: 2017
Publisher : 11th National Congress of metallurgy of Iran
By : Amin Haghizadeh, Ali Shafiei, Mohammad Ali Golzar, Mojtaba Kholaghi
File Information: persian Language/ 11 Page / size: 1,95 KB
سال : 1396
ناشر : يازدهمين كنگره ملي مهندسين متالوژی ايران
کاری از : امين اخباري زاده, علی شفيعي, محمدعلي گلعذار, مجتبي خلقي
اطلاعات فایل : زبان فارسی / 11 صفحه / حجم : KB 1,95
نقد و بررسیها
هنوز بررسیای ثبت نشده است.