توضیحات
چکیده
اعضاي سازه هاي فولادي عموما در محل اتصال و اجزاي آن، بيش از هر ناحيه ديگري در معرض تمركز تنش قرار دارند لكن در محاسبات معمول مهندسي ، اتصال و اجزاي آن بر مبناي تنش هاي اسمي طراحي مي شوند. ضرايب تمركز تنش و كرنش را به ترتيب برابر نسبت تنش (ويا كرنش) در محل وقوع تمركز تنش مانند لبه سوراخ به تنش (ويا كرنش) اسمي تعريف كنيم. با وارد شدن مصالح به محدوده غير خطي و باز توزيع تنش ها، ضريب تمركز تنش كاهش مي يابد اما به جاي آن ضريب تمركز كرنش با نرخ بالايي افزايش خواهد داشت،كه به اين پديده جهش كرنش گفته مي شود. اين پديده عامل اصلي شكست برخي اتصالات جوشي و يا پيچي مي باشد . در اين مقاله تلاش شده است بررسي عددي پديده جهش كرنش در رفتار اتصالات نيمه گيردار با ورق انتهايي صورت پذيرد. در ابتدا، بررسي نتايج يك مدل عددي ساخته شده از اتصال يك تير طره بصورت نيمه گيردار با ورق انتهايي جوش شده به بال ستون نشان مي دهد كه در ناحيه رفتار الاستيك مصالح، در محل هاي تمركز تنش (در كنج بال كششي تير)، ضرايب تمركز تنش و كرنش با يكديگر برابر و ثابت مي باشد، لكن با وارد شدن به محدوده غير خطي و باز توزيع تنش ها، ضريب تمركز تنش كاهش يافته و به عدد يك متمايل مي گردد،و اين در حالي است كه در همان نقاط، ضريب تمركز كرنش با نرخ بالايي افزايش مي يابد. هم چنين نتايج مشابهي در مطالعات عددي اتصال نيمه گيردار همان تير طره با ورق انتهايي پيچ شده براي تمركز تنش در لبه هاي سوراخهاي تعبيه شده در ورق انتهايي در ناحيه بال كششي بدست آمد. در مدلسازي عددي ديگر، اثر صفحات پر كننده بين ورق انتهايي و بال ستون بر پديده جهش كرنش بررسي شده است. نتايج نشان اد در حالتي كه ورق انتهايي به صفحه پر كننده زيرين خود با جوش متصل گردد، تمركز كرنش كاهش خواهد يافت.
مقدمه
اعضاي سازه هاي فولادي عموما در محل اتصال و اجزاي آن، بيش از هر ناحيه ديگري در معرض تمركز تنش قرار دارند و از آنجايي ه محاسبه و يافتن توزيع دقيق تنش هاي واقعي، كاري دشوار و وقت گير است لذا در محاسبات معمول مهندسي ، اتصال و اجزاي آن بر مبناي تنش هاي اسمي طراحي مي شوند.
ABSTRACT
The members of steel structures are generally exposed at the junction and its components more than any other area of stress concentration, but in the usual engineering calculations, the connection and its components are based on the nominal stresses. The stress and strain concentration coefficients are equal to the stress (or strain) ratio at the stress concentration site, such as the edge of the hole, to the stress (or strain) nominal. When the material enters the nonlinear range and the distribution of stresses again, the stress concentration coefficient decreases, but instead, the strain concentration coefficient will increase at a high rate, which is referred to as strain mutation. This phenomenon is the main cause of the failure of some welding or screw joints. In this paper, we attempt to study the numerical behavior of the strain mutation phenomenon in the behavior of semiconductor fittings with the end plate. In the first step, the results of a numerical model made from the coupling of a beam beam in the form of a semicircular with a finished sheet welded to the column wings show that, in the elastic behavior of the materials, in the stress concentration areas (in the tensile strength of the beam), the coefficients The stress and strain concentration are equal and constant, but by entering into the nonlinear range and re-distribution of stresses, the stress concentration coefficient is reduced to one, and at the same time, the coefficient Strain concentration increases at high rates. Similar results were obtained in numerical studies of the semiconductor connection of the same tin beam with a screwed end plate for stress concentration at the edges of the hole embedded in the end sheet in the tensile region. In numerical modeling, the effect of filler plates between the end of the sheet and the column head on the strain mutation phenomenon has been investigated. The results indicate that the strain concentration will decrease when the bottom plate is connected to the bottom plate of the weld itself.
INTRODUCTION
The members of steel structures are generally exposed at the junction and its components more than any other region of stress concentration, and since it is difficult to calculate and find the exact distribution of real tensions, it is difficult and time consuming. Therefore, in the usual calculations of engineering, Its components are based on nominal stresses.
Year: 2011
Publisher : Sixth National Congress on Civil Engineering
By : Mohammad Saeed Karimi, Naser Zolfaghar
File Information: persian Language/ 8 Page / size: 629 KB
Only site members can download free of charge after registering and adding to the cart
سال : 1390
ناشر : ششمین کنـگره ملی مهنـدسی عمـران
کاری از : محمد سعيد كريمي ، ناصر ذوالفقار
اطلاعات فایل : زبان فارسی / 8 صفحه / حجم : KB 629
نقد و بررسیها
هنوز بررسیای ثبت نشده است.