توضیحات
خلاصه
در این مقاله مبانی تعیین حداقل آرماتور كششی براي اعضاي خمشي سازه هاي بتن مسلح بررسي گردیده و توصيه هاي تعدادي از آئین نامه هاي طراحي سازه هاي بتن مسلح در این خصوص مقايسه و درمورد نزدیکی توصيه هاي آنها با مباني مزبور اظهار نظر شده است. از طرف ديگر، از آنجا كه توصيه های آئين ها هي نامه ها عمدتا براي مقاطع مستطيلي است، برا تعیین حداقل آرماتور خمشي در مقاطع با اشكال ديگر روابط پیشنهاد گردیده است. در انتها با ارائه تعدادي مثال عددي روابط مزبور ارزيابي شده است.
مقدمه
در طراحي سازه ها گاهي به دلیل ملزومات معماري یا عملكرد مورد انتظار، ابعاد تیر به مراتب بزرگتر از مقادیری كه براي خمش لازم است، انتخاب ميشود. چنین مقاطعي به صورت تئوري مقادیر بسیار كمي فولاد كششي لازم دارند. اما این مساله ممكن است حالت شكست محتمل ديگري را برای تیر به شدت كم فولاد پيش آورد؛ به صورتي كه مقاد نهايي مقطع از لنگر ترك خوردگي آن كمتر باشد و تیر بلافاصله پس از ترك خوردگي گسیخته شود. به همین دلیل آیین نامه ها حداقل فولاد كششي لازم در مقطع را چنان تعیین میكنند كه بلافاصله پس از ترك خوردگي شكست ترد اتفاق نيفتد. حداقل فولاد خمشي در آبا دقيقا مشابه حداقل فولاد در ACI 318تعيين شده است. اين مقدار آرماتور در مقاطع مستطيلي به چهار عامل مقاومت بتن، تنش تسليم فولاد، عرض مقطع و ارتفاع موثر مقطع وابسته است. منطق رابطه اي كه امروزه مورد استفاده بسياري از آيين نامه ها، كتابهاي سازه هاي بتني و پژوهشگران با موضوعيت حداقل آرماتور كششي قرار مي گيرد .اين است كه ابتدا لنگر ترك خوردگي يك مقطع بتني مستطيل شكل را بدون آرماتور خمشي بر اساس تنش هاي كششي ناشي از اين لنگر محاسبه ميكنند. سپس براي همين لنگر محاسبه شده براي يك مقطع مستطيلي با همان ابعاد و اين بار با فرض ترك خوردگي در ناحيه كششي مقدار آرماتور مورد نياز را محاسبه ميكنند. اين مقدار فولاد در واقع حداقل آرماتور كششي در اعضاي خمشي است.
ABSTRACT
In this paper, the basics of determining the minimum tensile reinforcement for bending members of reinforced concrete structures have been investigated and recommendations of a number of designing codes for reinforced concrete structures have been compared in this regard, and the recommendations of their recommendations have been commented on these principles. On the other hand, since the recommendations of the rites are mainly for rectangular sections, it is suggested to determine the minimum bending reinforcement in sections with other forms of relations. Finally, a number of numerical examples of these relationships have been evaluated.
INTRODUCTION
In structural design, sometimes due to the requirements of the architecture or expected performance, the dimensions of the beam are much larger than the values required for bending. Such sections, in theory, require a very small amount of tensile steel. But this may lead to another possible failure condition for a very light steel beam, such that the final value of the cross section is less than the anchor point and the beam is immediately broken off after cracking. For this reason, the regulations specify at least the necessary tensile steel at the cross-section so that failure to crack immediately after cracking does not occur. Minimum steel bending in AB is exactly the same as the minimum steel in ACI 318. This amount of reinforcement in rectangular sections depends on four factors of concrete strength, steel delivery stress, section width and effective height of the section. The relationship logic that is used today by most of the rules, the books of concrete structures and the researchers with the subject of at least the tensile reinforcement. First, the anchoring of a rectangular concrete cross section without a curved reinforcement based on tensile stresses They calculate this anchor. Then for the same anchor calculated for a rectangular cross section with the same dimensions and this time, with the assumption of cracks in the tensile region, calculates the amount of reinforcement required. This amount of steel is at least a tensile reinforcement in the bending members.
Year: 2011
Publisher : Sixth National Congress on Civil Engineering
By : Ehsan Alizadeh , Mohammad Javad Fadaei
File Information: English Language/ 5 Page / size: 154 KB
Only site members can download free of charge after registering and adding to the cart
سال : 1390
ناشر : ششمین کنـگره ملی مهنـدسی عمـران
کاری از : احسان عليزاده ، محمد جواد فدائي
اطلاعات فایل : زبان فارسی / 5 صفحه / حجم : KB 154
نقد و بررسیها
هنوز بررسیای ثبت نشده است.