توضیحات
چکیده
در اين تحقيق تاثير عمليات حرارتي بر روي خواص مكانيكي بعدي آلياژ 15-5PHبررسي شده است. عمليات حرارتي بر روي آلياژ بصورت عمليات انحلالي و سپس عمليات پيرسختي در دماي 450درجه سانتيگراد و براي مدت زمان هاي 1تا 6ساعت انجام شد. تاثير عمليات حرارتي بر خواص بعدي بصورت تغييرات سختي، تنش تسليم و استحكام كششي در دماي محيط ارزيابي گرديد. نتايج سختي سنجي و تستهاي كشش حاكي از تشكيل فاز ثانويه جديد در طول عمليات پيرسختي است، كه اين فاز همان رسوبات کوهِرنت غني از مس ميباشند. همچنين اين نتايج نشان دهنده ماكزيمم خواص در فرآيند يرسختي براي مدت زمان 6ساعت در نتيجه رسوب پيوسته اين فاز هستندكه سرعت تشكيل آنها با گذشت زمان كاهش مييابد. افزايش خواص كششي ناشي از برهمكنش بين نابجايي ها و رسوبات مس ميباشد. ريزسختار نمونه ها نيز در دو مرحله عمليات حرارتي توسط ميكروسكوپ نوري و الکتروني SEM بررسی شد.
مقدمه
فولادهاي زنگنزن رسوب سخت شونده داراي مقاومت به خوردگي و مقاومت در برابر زنگزدن در دماهاي بالا، به همراه حفظ حداکثر استحکام کششي در دماهايي حدوداً پايينتر از 450درجه سانتيگراد هستند. بسته به نوع کاربرد ممکن است اين آلياژها در شرايط آنيل شده(عمليات حرارتي انحلالي) يا در شرايط آنيل بعلاوه پيرسخت (رسوب سخت) شده، مورد استفاده قرار گيرند. در برخي موارد به منظور راحت تر کردن فرآيندهاي بعدي شکل دهي، ممکن است اين آلياژها در شرايط فراپيرسخت شده تهيه شوند. توسط تغيير پارامترهاي فرآيند پير (رسوب سخت) کردن، امکان دسترسي به محدوده وسيعي از خواص مطلوب در اين آلياژها وجود دارد. فولاد زنگنزن 15-5PHجزء گروه مارتنزيتي فولادهاي زنگ نزن رسوب سخت شونده ميباشد، اين فولادها براي ساخت قطعات متفاوتي همچون پره هاي توربين و همچنين قطعات در معرض دما و تنش هاي بالا در صنعت هسته اي مورد استفاده هستند. عمليات حرارتي اين فولاد در ابتدا شامل عمليات انحلالي آنيل کردن و سپس پيرسخت(رسوب سخت) کردن در دما و زمان مناسب با توجه به خواص مورد نياز است. بر اساس تحقيقات صورت گرفته روي نوع رسوبات و شکل گيري آنها در طول عمليات حرارتي اين فولاد، افزايش سختي در طول فرآيند پيرسختي ناشي از تشکيل رسوبات غني از مس است.
ABSTRACT
In this research, the effect of heat treatment on the mechanical properties of the next alloy of 15-5PH is investigated. Thermal treatment on the alloy was carried out at soldering and then at a temperature of 450 ° C for a duration of 1 to 6 hours. The effect of heat treatment on the next properties was evaluated in terms of hardness, tensile stress and tensile strength at ambient temperature. Hardness tests and tensile tests indicate the formation of a new secondary phase during the operation, which is the same as copper rich copernic sediments. Also, these results show the maximum properties of the elasticity process for a period of 6 hours as a result of the continuous sedimentation of this phase, which decreases their rate of formation over time. The increase in tensile properties is due to the interaction between dislocations and copper deposits. The microstructure of the specimens was also studied in two stages of heat treatment by light microscopy and electron microscope (SEM).
INTRODUCTION
Sintering steels of hardening sediment have corrosion resistance and rust resistance at high temperatures, along with maintaining maximum tensile strength at temperatures below about 450 degrees centigrade. Depending on the application, these alloys can be used under annealed conditions (dissolution heating operations) or under annealing conditions, as well as tightly deposited. In some cases, in order to facilitate subsequent shaping processes, these alloys may be prepared in a superficial condition. By changing the parameters of the old process (hardening sediment), it is possible to access a wide range of desired properties in these alloys. The stainless steel 15-5PH is part of the martensitic group of hardening stainless steels, these steels are used to make different components, such as turbine blades, as well as components exposed to high temperature and tension in the nuclear industry. The heat treatment of this steel initially involves annealing and then desiccation (hardening) at a temperature and time appropriate to the properties required. According to research on the type of sediment and its formation during the thermal treatment of this steel, increasing stiffness during the process is due to the formation of copper-rich sediments.
Year: 2007
Publisher : 11th National Congress of metallurgy of Iran
By : Alireza Zargaran, Mehrdad Aghaei Khafari
File Information: persian Language/ 11 Page / size: 341 KB
سال : 1386
ناشر : يازدهمين كنگره ملي مهندسين متالورژی ايران
کاری از : عليرضا زرگران ،مهرداد آقايي خفري
اطلاعات فایل : زبان فارسی / 11 صفحه / حجم : KB 341
نقد و بررسیها
هنوز بررسیای ثبت نشده است.