توضیحات
چکیده
كامپوزيتهاي Al-Mg2Siكه به روش ريخته گري تهيه مي شوند، پيشتر به عنوان دسته جديدي از مواد بسيار سبك شناخته شده اند و تاكنون تلاشهاي زيادي در جهت اصلاح ساختار شكننده Mg2Siاوليه در اين آلياژها صورت گرفته است. در اين تحقيق اثرات افزودن ليتيم و زيركونيم به آلياژ Al-15%Mg2Siبررسي شده است.با استفاده از ميكروسكوپ نوري ، آناليز تصويري و ميكروسكوپ الكتروني(SEM) نشان داده شد كه ليتيم در ريز كردن ساختار درشت Mg2Siاوليه بسيار موثر بوده و اندازه متوسط اين ذرات را از 30 µmبه حدودا 6 µmمي رساند.گذشته از ريزنمودن ساختار شكل اين ذرات را از چند وجهي هاي غير منظم و رخدار به اشكال نيمه رخ دار منظم با توزيع منظم تر در زمينه تبديل مي كند.ليتيم، به علاوه، تاثير آشكاري در ريز نمودن ساختار يوتكتيك زمينه دارد.افزودن زير كونيم به ميزان %0.01ساختار نسبتا ريزي ايجاد مي كندو شكل و توزيع Mg2Siاوليه را به ضعيتي منظم تغيير مي دهدام افزودن آن تا %0.1 مجددا سبب درشت شدن ساختار مي شود.
مقدمه
كامپوزيت هاي پايه آلومينيوم و منيزيمي كه با ريزذرات فاز بين فلزي Mg2Siتقويت شده اند، اخيرا به عنوان گروه ديدي از كامپوزيتهاي زمينه فلزي MMCsدر دنيا معرفي شده اند. اين آلياژها مزيت هايي مانند دانسيته كم، مقاومت به سايش و قابليت ريختگي خوب را ارايه مي كنند. آلياژهاي Al-Mg2Si كانديد مناسبي براي جايگزيني آلياژهاي Al-Siدر موتور اتوموبيل ها و قطعات هواپيما هستند.آماده سازي درجاي (Insitu) اين كامپوزيتها با توجه به مزيتهاي توزيع مناسب فاز تقويت كننده، ترشوندگي خوب ذرات و هزينه هاي كم توليد ؛بهترين راه فرآوري به نظر میرسد. به رغم اينكه ذرات بين فلزي Mg2Si دماي ذوب بالا، دانسيته كم، سختي بالا، ضريب انبساط حرارتي پايين و فصل مشتركي تعادلي دارند، مورفولوژي درشت و شكننده آنها منجر به انعطاف پذيري كم اين آلياژها مي شود. بنابراين تحقيقاتي در جهت ريز نمودن ساختار Mg2Siاوليه و نيز ساختار يوتكتيك Alو Mg2Siانجام گرفته است تا در نتيجه خواص مكانيكي اين آلياژها ارتقا داده شود. علاوه بر روشهاي گراني مانند انجماد سريع و آلياژسازي مكانيكي دو روش عمده استفاده از سرعت سرد كردن بالا و بهسازي به كمك افزودن عناصر آلياژي جهت ارتقاي ساختار شكننده فاز اوليه در اين آليازها به كار گرفته مي شود.
ABSTRACT
Al-Mg2Si composites made by casting are known as a new category of lightweight materials, and much effort has been made to correct the fragile Mg2Si structure in these alloys. In this study, the effects of adding lithium and zirconium to Al-15% Mg2Si alloy were investigated. Using optical microscopy, image analysis and electron microscopy (SEM), it was shown that lithium is very effective in reducing the coarse structure of the Mg2Si and its moderate size The particles ranging from 30 μm to about 6 μm. After disregarding the shape of the particle, they convert these particles from non regular and occasional multifaceted to semi-regular forms with more regular distribution. Lithium, in addition, has a clear effect on The reduction of the eutectic structure of the background is possible. Increasing the subunit by 0.01% produces a relatively small structure, and the formation and distribution of the first Mg2Si The main change to regular status Dhdam adding it to 0.1%, again due to the coarse structure.
INTRODUCTION
Aluminum and magnesium base composites reinforced with Mg2Si intermetallic microparticles have recently been introduced as a group of metal composite metal MMCs in the world. These alloys offer advantages such as low density, abrasion resistance, and good casting ability. Al-Mg2Si alloys are a suitable candidate for the replacement of Al-Si alloys in automobile engines and aircraft parts. The insitu’s production of these composites is based on the advantages of proper distribution of the reinforcing phase, good wettability of particles and low cost of production; the best way of processing It seams. Despite the fact that intermetallic Mg2Si particles have a high melting point, low density, high hardness, low coefficient of thermal expansion, and a common interface, their coarse and fragile morphology leads to a low flexibility of these alloys. Therefore, research has been done to fine-tune the structure of the Mg2Si as well as the eutectic structure of Al and Mg2Si to improve the mechanical properties of these alloys. In addition to expensive methods such as rapid freezing and mechanical alloying, two major methods of using high cooling rate and refinement with the addition of alloying elements are used to enhance the fragile structure of the initial phase in these alkalis.
Year: 2007
Publisher : 11th National Congress of metallurgy of Iran
By : Raheleh Hadian, Naser Varhamam, Masoud Emami and Narges Nemati
File Information: persian Language/ 11 Page / size: 10,40 KB
سال : 1386
ناشر : يازدهمين كنگره ملي مهندسين متالورژی ايران
کاری از : راحله هاديان ,ناصر ورهرام , مسعود امامي و نرگس نعمتي
اطلاعات فایل : زبان فارسی / 11 صفحه / حجم : KB 10,40
نقد و بررسیها
هنوز بررسیای ثبت نشده است.