توضیحات
چکیده
آزمايش ديناميك شمع، PDAمعمولا براي تعيين ظرفيت باربري نهايي استاتيكي شمع بكار ميرود. اين آزمايش با اتصال سنسورهاي شتاب سنج و كرنش سنج به شمع و اعمال ضربه چكش شمع كوب به سر شمع با استفاده از تحليل گر شمع كوبي و با تبديل انرژي ديناميكي به معادل استاتيكي آن انجام مي شود. همچنين علاوه بر ظرفيت باربري اطلاعات ديگري نظير سلامت شمع، تنش هاي فشاري و كششي و انرژي شمع كوب را ميتوان از PDAدريافت كرد. در پروژه اسكله و موج شكن مجتمع پرورش ميگوي روديك از شمع يا هاي لوله فولادي با قطر 508ميليمتر و ضخامت / 12 7ميليمتر استفاده شده است. با توجه به اينكه طراحي انجام شده در اين پروژه با مشكلاتي در اجرا مواجه شد، آزمايش ديناميك شمع، ،PDAبر روي 4شمع آزمايشي به منظور امكان سنجي كوبش شمع هاي لوله اي فلزي ها و برآورد ظرفيت باربري شمع انجام گرفت. در طراحي اوليه شمع ها با طول 12متر و ظرفيت باربري نهايي 1000 kNدر نظر گرفته شده بود. اما در اجرا، نفوذ شمع ها بيش از 6متر به كوبش سخت منتهي شده و لهيدگي در محل ضربه چكش مشاهده گرديد كه با انجام آزمايش هاي PDAلهيدگي سر شمع ها كنترل شده و نيز ظرفيت باربري شمع با طول قابل نفوذ بدست آمد . نتايج نشان داد كه ميتوان با طول نفوذي حدود نصف طول در نظر گرفته شده در طراحي اوليه (نفوذ حدود 6متر) به ظرفيت باربري بيشتري از طراحي اوليه رسيد و همچنين از لهيدگي سر شمع جلوگيري كرد.
مقدمه
گرچه روش هاي علمي طراحي شمع در دهه هاي اخير داراي پيشرفت چشمگيري بوده، اما هنوز مهمترين بخش طراحي شمع، يعني تعيين ظرفيت باربري محوري، به شدت به نتايج تجربي وابسته است ( Randolph,2003). شيوه زيادي براي تعيين ظرفيت باربري شمع ها مانند تحليل های استاتيكی ، فرمول های ديناميكی ، تحليل معادله موج، آزمايش بارگذاري استاتيكي و آزمايش ديناميكي (PDA) وجود دارد. دقيقترين روش براي تعيين ظرفيت باربري شمع ها، انجام آزمايش های استاتيك و ديناميك شمع است. در آزمايش بارگذاري استاتيكي فشاري، شمع يك بارگذاري مرحله اي استاتيكي را همانند شرايط واقعي تجربه ميكند. در زمان انجام آزمايش ميزان بار وارده بر سر شمع و تغيير شكل قائم آن به دقت اندازه گيري ميگردد.
ABSTRACT
The PDA Dynamic Test is usually used to determine the static final stacking capacity of the pile. This test is carried out by connecting the accelerometer and strain gauges to the candle and applying the hammer blow hammer to the candle head using a pile analyzer and by converting the dynamic energy to its static equivalence. In addition to the loading capacity, other information such as candle health, stress and tensile stresses and energy of a candle can be received from the PDA. In the project of the berth and bream of the shrimp shrimp, Rodik has been used for 508 mm diameter steel pipes and 7.12 mm thick tubes. Considering the design problems encountered in this project with the implementation problems, the Dynamic Candle Experiment, PDA was conducted on 4 experimental piles in order to feasibility of knocking metal tube piles and estimating the capacity of piling. In the initial design, piles with a length of 12 meters and a final load capacity of 1000 kN were considered. But in the run-up, the penetration of the piles by more than 6 meters resulted in a hard knock and a hammer blow was detected. By conducting PDA experiments, the pile head plugs were controlled and the bearing capacity of the permeable pile was obtained. The results showed that with an infiltration length of about half the length considered in the initial design (penetration of about 6 meters), it was possible to carry more capacity from the original design and also prevented the candle head from burning.
INTRODUCTION
Although the scientific methods of candle design have been remarkable in recent decades, yet the most important part of the design of the pile, namely the determination of axial load capacity, is strongly dependent on empirical results (Randolph, 2003). There are many ways to determine the capacity of piles to load, such as static analyzes, dynamic formulas, wave equation analysis, static loading tests, and dynamic tests (PDAs). The most accurate method for determining the bearing capacity of piles is to conduct static and dynamic tests of the pile. In a static compression test, the candle experiences a static static loading as it is in real condition. At the time of the test, the load on the pile and its vertical deformation are carefully measured.
Year: 2011
Publisher : Sixth National Congress on Civil Engineering
By : Kazem Fakharian, Iman Hosseinzadeh Attar
File Information: persian Language/ 8 Page / size: 338 KB
Only site members can download free of charge after registering and adding to the cart
سال : 1390
ناشر : ششمین کنـگره ملی مهنـدسی عمـران
کاری از : كاظم فخاريان ،ايمان حسين زاده عطار
اطلاعات فایل : زبان فارسی / 8 صفحه / حجم : KB 338
نقد و بررسیها
هنوز بررسیای ثبت نشده است.