توضیحات
چکیده
يكي از مسائل مهم در شكل دادن گرم ورقهاي فولادي پديده ي تبلور مجدد استاتيكي است. اين پديده بر روي شكل و اندازه دانه هاي آستنيت اثر مي گذارد و باعث تغيير در ريزساختار فولاد، تغيير خواص مكانيكي و ف كيزي ي فولاد مي گردد. بعلت توزيع غير يكنواخت دما، سرعت كرنش، ميزان كرنش و ساير پارامترهاي موثر بر سينتيك تبلور مجدد اعمالي در حين فرآيند نورد، ميزان كسر تبلور مجدد يافته در نواحي مختلف ورق متفاوت مي باشد و در نتيجه ريزساختار و خواص متالورژيكي و مكانيكي در نواحي مختلف با هم متفاوت مي باشد. بنابراين بررسي اين پديده و تاثير پارامترهاي نورد بر آن از اهميت خاصي برخوردار است. در اين مقاله با استفاده از روش اجزاء محدود به صورت حل همزمان معادلات حرارت و معادلات تغيير فرم پلاستيك پارامترهايي نظیر توزيع دما، سرعت كرنش و كرنش بدست مي آیند. سپس از يك شبكه ي عصبي آموزش يافته با استفاده از نتايج بدست آمده از مرحله قبل به پيش بيني كسرحجمي تبلور مجدد يافته پرداخته مي شود.
مقدمه
تا كنون روشهاي متفاوتي براي بررسي فرآيند نورد پيشنهاد گرديده است. در تحقيقات انجام گرفته فرآيند نورد بصورت ترمومكانيكال در نظر گرفته شده و از نتايج آن براي بررسي فرايندهاي متالورژيكي استفاده شده است. يكي از روشهايي كه در دو دهه ي اخير مورد توجه محققين قرار گرفته روش المان محدود است. عموم تحقيقات انجام گرفته توسط اين افراد بصورت دو بعدي و بصورت ترمومكانيكال انجام گرفته است. از اوايل دهه ي نود ميلادي در تحقيقات انجام گرفته مسائل متالورژيكي نيز مورد توجه قرار گرفت. در سال Pietrzyk 1990از اين روش براي پيش بيني توزيع كسر تبلور مجدد يافته و توزيع اندازه دانه در نورد گرم استفاده نمود. محققين با استفاده از روابط نيمه تجربي و آناليز المان محدود به ارزيابي كسر تبلور مجدد يافته و اندازه دانه ها نموده اند. به علت تجربي بودن روابط بكار رفته دراين گونه ارزيابي ها محدوديت هايي در زمينه ي تركيب آلياژ و پارامترهاي فرآيند تغيير فرم وجود دارد و اين روابط در يك محدوده ي مشخص كارآيي دارند و روابطي عمومي براي تمام كاربردها نيستند.
ABSTRACT
One of the important issues in the formation of hot plate steel is the phenomenon of static re-crystallization. This phenomenon affects the shape and size of the austenite grains and causes a change in the microstructure of the steel, the mechanical and mechanical properties of the steel. Because of the uneven distribution of temperature, strain rate, strain rate and other parameters affecting the re-crystallization kinetics during the rolling process, the residual crystallization fraction in different areas of the sheet is different, resulting in the microstructure and metallurgical and mechanical properties in different regions with It is different. Therefore, it is important to study this phenomenon and the effect of rolling parameters on it. In this paper, using the finite element method in the form of simultaneous solving of heat equations and plastic equilibrium equations, parameters such as temperature distribution, strain rate and strain are obtained. Then, from a trained neural network, using the results obtained from the previous step, the reciprocal crystallization prediction is considered.
INTRODUCTION
So far, different methods have been proposed to investigate the rolling process. In the research, the rolling process is considered thermomechanical and its results are used for the investigation of metallurgical processes. One of the methods that has been considered by researchers in the last two decades is the finite element method. Public research done by these people has been done in two dimensions and thermomechanical. Metallurgical issues have also been taken into consideration since the early 90’s. In Pietrzyk 1990, this method was used to predict the crystallization fraction distribution and to use grain size distribution in hot rolling. The researchers, using quasi-experimental and finite element analysis, have evaluated the crystallization fraction and size of the seeds. Due to the empirical nature of the relationships used in this evaluation, there are limitations in the composition of the alloy and the parameters of the process of changing the form, and these relationships are in a certain range of efficiency and are not general relations for all applications.
Year: 2007
Publisher : 11th National Congress of metallurgy of Iran
By : Majid Seyyed Salehi, Siamak Serajzadeh
File Information: persian Language/ 11 Page / size: 327 KB
سال : 1386
ناشر : يازدهمين كنگره ملي مهندسين متالورژی ايران
کاری از : مجيد سيد صالحي ، سیامك سراج زاده
اطلاعات فایل : زبان فارسی / 11 صفحه / حجم : KB 327
نقد و بررسیها
هنوز بررسیای ثبت نشده است.