توضیحات
چکیده
در اين مقاله كامپوزيت سراميك پليمري با پودر نانوسايز زيركونات تيتانات سرب تهيه شده از طريق سل ژل آلكوكسيدي و پليمر پلي وينيل كلروايد تهيه شده و خواص الكتريكي اين كامپوزيت بر حسب كسر حجمي جز سراميك مورد مطالعه قرار گرفته شد. مطالعه ريز ساختار كامپوزيت نشان داد كه ريز ساختار ريز و كاملا هموژن در كامپوزيت حاصل شده است ، همچنين داده هاي بررسي هاي الكتريكي نشان داد كه با افزايش جز حجمي سراميكي ثابت دي الكتريكي افزايش يافته است، اين افزايش به مراتب بيشتر از انواع سنتي كامپوزيت مذكور بوده و خواص الكتريكي آن مشابه كامپوزيت هاي 1-3مي باشد. بدين ترتيب مي توان از خواص بهينه و قابل كنترل نانوپودر PZTبدون تغيير در اثر زينتر در كاربردهاي الكترومكانيكي خاص استفاده كرد.
مقدمه
زيركونات تيتانات سرب Pb(ZrxTi1-x)O3با تركيب باند مرزي مورفوتروپيك x =47يكي از مهمترين مواد پيزوالكتريك بوده كه كاربردهاي متنوعي در صنايع الكترونيك شامل حسگرها، راه اندازها، محركها و مبدلها را دارا مي باشد.اما اين سراميك ها امپدانس اكوستيكي بالا و سازگاري ضعيف اكوستيكي با آب و محيط هاي اطراف داشته و نيز ترد و شكننده بوده و امكان ساخت اشكال پيچيده محدودي را دارند . براي رفع اين عيب از اوايل دهه هفتاد كامپوزيت هاي سراميك پليمر توسعه يافتند . در اين راستا از انواع پليمر هاي پلي اورتان، اتيلن پروپيلن ، اپوكسي و پلي وينيل كلرايد استفاده شده است. اين نوع پيزوسراميك ها در كاربردهايي كه نياز به وسيله تبديل انرژي اكوستيك به امواج الكتريكي با امپدانس اكوستيك پايين در محيط آبي نياز است مانند هيدروفون هاو پروب هاي سونوگرافي در تصوير برداري پزشكي و دستگاه هاي سونار بكار مي روند. علاوه بر نوع مواد سازنده، نحوه اتصال اجزا نيز در خواص نهايي كامپوزيت تاثير داشته و انواع كامپوزيت هاي 0-3 ،1-3و نيز 2-2ساخته شده اند ,كه اعداد ذكر شده ديمانسيون هاي جز سراميكي و زمينه را نشان مي دهد. در طي دهه اخير محققين مختلفي بر روي انواع فرايند هاي ساخت كامپوزيت كار كرده اند، من جمله روش ميله گذاري، برشكاري، تزريق در قالب، قالب فدا شونده، صفحه چيني، دي الكتروفورسيس، اكستروژن همزمان، خودنظم دهنده و نيز روش متداول مخلوط اكسيدها كه هر كدام ويژگي هاي مختلفي از خود نشان ميدهد.
ABSTRACT
In this paper, polymer composite ceramic composite with nanosized powder of lead titanate zirconium was prepared by sol-gel alkoxide and polyvinyl chloride polymer, and the electrical properties of this composite in terms of volume fraction except ceramic were studied. The study of composite microstructure showed that fine and completely homogeneous microstructure was obtained in the composite. Also, the electrical data showed that the dielectric constant increased with increasing ceramic volume component, this increase was much higher than the traditional types of composite And its electrical properties are similar to 1-3 composites. In this way, the optimum and controllable properties of PZT nanopowders can be used without any change in the effect of zinc in specific electromechanical applications.
INTRODUCTION
Pb (ZrxTi1-x) O3 titanate zirconium with a morphotropic boundary bond composition of x = 47 is one of the most important piezoelectric materials that has various applications in the electronic industry including sensors, actuators, actuators and converters. However, these ceramics have high ecosystem impedance and The weak ecosystem compatibility with water and surrounding environments is also crisp and fragile, making it possible to produce limited complex shapes. To overcome this defect, ceramic polymer composites have been developed since the early 1970s. Polyurethane, ethylene-propylene, epoxy and polyvinyl chloride polymers have been used for this purpose. This kind of piezoceramics is needed in applications that require the conversion of acoustic energy to electrical acoustic waves with a low ecosystem impedance in aqueous media, such as hydrophones and ultrasound probes in medical imaging and sonar devices. In addition to the type of material, the method of connecting the components also affected the final properties of the composite, and a variety of composites of 0-3, 1-3 and 2 have been constructed, which show the numbers mentioned except ceramic and background. Over the past decade, various researchers have been working on a variety of composite manufacturing processes, including cutting techniques, cutting, injection molding, sacrificial molding, china, di-electrophoresis, co-extrusion, self-regulating and conventional oxide mixing Each of them has different characteristics.
Year: 2007
Publisher : 11th National Congress of metallurgy of Iran
By : Shahab Khameneh Asl
File Information: persian Language/ 9 Page / size: 426 KB
سال : 1386
ناشر : يازدهمين كنگره ملي مهندسين متالورژی ايران
کاری از : شهاب خامنه اصل
اطلاعات فایل : زبان فارسی / 9صفحه / حجم : KB 426
نقد و بررسیها
هنوز بررسیای ثبت نشده است.