توضیحات
چکیده
با استفاده از آزمايش پيچش گرم در دماي پايين، تاثير نرخ كرنش اعمالي در منطقه بحراني (α + γ) بر رفتار تغيير شكل پلاستيك و برميزان ريز شدن دانه هاي فريت در يك فولاد كم كـربن ميكروآليـاژي داراي Nb-Ti مطالعـه شـد. از روي منحنـي هـاي سـيلان گـرم فريـت و بـا اسـتفاده از ميكروسـكوپ نـوري و ديفراكسـيون الكترون هاي برگشتي ،(EBSD) Electron back scattered diffraction فرآيندهاي نرم شدن ديناميكي در فريت در حين تغيير شكل و تحولات صورت گرفته در ريزساختارها مورد تجزيه و تحليل قرار گرفت. مشـاهدات نشـان مـي دهد در حين تغيير شكل در منطقه دو فازي، دانه هاي ريز و هـم محـور فريـت(Equiaxed fine ferrite grains (EFG در ريزساختار پديدار مي شوند. شواهد مبين آن است كه ايـن دانـه هـاي EFGدر جريـان وقـوع تبلـور مجـدد ديناميكي پيوسته در (Continuous dynamic recrystallization (CDRXفاز فريت ايجاد گشته اند. همچنـين ديـده مـي شود افزايش نرخ كرنش اثر مثبت بر فرآينـد ريـز شـدن دينـاميكي دانـه هـاي فريـت بـا مكـانيزم CDRXدارد. بطوريكه با افزايش اين پارامتر، اندازه دانـه هـاي فريـت EFGحاصـل از CDRXكـاهش و كسـر حجمـي آنهـا افزايش مي يابد. اما، با كاهش نرخ كرنش دانه هاي صلي و دانه هاي فرعي دچار رشد شـده و امكـان دسـت يابي به ريزساختار نهايي ريز دانه ميسر نمي شود.
مقدمه
امروزه بخاطر نقش منحصر بفرد تاثير ريز كردن دانه هاي فريت بر خواص مهندسي محصولات فولادي؛ ايـن روش بطور قابل ملاحظه اي در كانون توجه محققين قرار دارد. بطوريكه ديده شده است اگر دانه هاي فريـت در ريز ساختار نهايي تا حد 1ميكرون ريز شوند، آنگاه مي تـوان تعـداد زيـادي از انـواع مختلـف فولادهـاي آلياژي و گران قيمت را با فولادهاي ساده كربني ريز دانه جايگزين نمود. بررسيها نشان مي دهـد بيشـتر مطالعات انجام گرفته در ارتباط با ريز كردن دانه هاي فريت با روشهاي نوين ترمومكانيكي، عمدتاً در ارتبـاط با تغيير شكلهاي دماي بالا (Hot deformation) است. در خصوص تغيير شـكل در دمـاي پـايين (Warm deformation) فولادها اطلاعات كمتري در دسترس است، در اين رمينه اطلاعاتي هم كه منتشـر شـده اسـت بيشـتر در مـورد فولادهاي ساده كربني و فولادهاي IFمي باشد. بالاخص در خصوص تاثير پارامترهاي تغييـر شـكل گرم در دماي پايين بر روي ميزان ريز شدن دانه هاي فريت در فولادهاي ميكروآلياژي اطلاعـات چنـداني در دسترس نيست.
ABSTRACT
Using the hot torsion test at low temperature, the effect of applied strain rate in the critical region (α + γ) on the plastic deformation behavior and on the degree of ferrite graining was studied in a Nb-Ti microalloy steel. Electron back scattered diffraction (EBSD) was used to simulate dynamic softening processes in the ferrite during transformation and microstructure changes, using gravity flute curves and electron microscopy (EBSD). Observations show that, during the deformation in the two-phase region, fine-grained and equiaxed fine ferrite grains (EFG) appear in the microstructure, indicating that these EFG grains occur during the continuous recrystallization of ( Continuous dynamic recrystallization (CDRX) has been created, and there is also a positive effect on increasing the rate of strain on the process of fragmentation of the ferrite grains with the CDRX mechanism, so that by increasing this parameter, the size of the EFG ferrite grains from the CDRX decreases and their volume fractions increase However, by decreasing the strain rate, there are seminal seeds and seedlings It is not possible to reach the final microstructure of fine grains.
INTRODUCTION
Today, due to its unique role, the effect of fritting grains on the properties of engineering steel products; this method is considerably in the focus of attention of researchers. As it has been seen, if the ferrite grains in the final microstructure are reduced to 1 micron, then a large number of different types of alloyed and expensive steels can be replaced with fine carbon fine grain steels. Studies show that most of the studies carried out on the fractionation of ferrite grains with modern thermomechanical methods, mainly related to the deformation of hot forms. More information is available on steel at a lower temperature (Warm deformation), in which more information is available on plain carbon steel and IF steels. Particularly, there is not much information about the effect of hot-flame deformation parameters at low temperatures on the amount of ferrite grains in microalloy steels.
Year: 2007
Publisher : 11th National Congress of metallurgy of Iran
By : Baitollah Iqbali
File Information: persian Language/ 13 Page / size: 752 KB
سال : 1386
ناشر : يازدهمين كنگره ملي مهندسين متالورژی ايران
کاری از : بيت اله اقبالي
اطلاعات فایل : زبان فارسی / 13 صفحه / حجم : KB 752
نقد و بررسیها
هنوز بررسیای ثبت نشده است.