توضیحات
خلاصه
يكي از مهمترين و ارزانترين مصالح موجود كه در دنيا كاربرد وسيعي دارد، بتن است. مزاياي كه بتن موجب شده است كه مورد علاقه اكثر مهندسين، طراحان و كارفرمايان باشد. مزاياي عمده بتن، مقاومت فشاري خوب، امكان بكارگيري آن در اغلب مناطق جغرافيايي، استفاده از مصالح طبيعي و ارزان، دارا بودن هزينه كم در مقابل حجم عمليات زياد، شكلدهي آن با توجه به اشكال هندسي طرح، امكان مكانيزه كردن عمليات، عدم نياز به نگهداري پرخرج در طول عمر بهره برداري و . . . است. اما بتن در نمودار تنش- كرنش داراي شيب نزولي تندي است. كاهش سريع مقاومت فشاري در ناحيه بعد از پيك بار به شكل معلومي موجب مود تردشكني گسيختگي ميشود. برا ي بهبود شكل پذيري بتن يك راهكار وجود دارد و آن افزودن الياف به بتن مي باشد. هزينه تهيه الياف توليد شده در كارخانه زياد ميباشد. با توجه به فراواني زائدات فلزي موجود در قطب هاي صنعتي كشور و حتي در كارگاه هاي كوچك، در اين مطالعه از تفاله هاي توليد شده در كارگاه هاي جوشكاري و تراشكاي به عنوان الياف براي تسليح بتن استفاده شده است. در اين تحقيق از تراشه هاي فولادي مارپيچي در نسبت هاي حجمي 0/40و 0/80و 1/2درصد استفاده شده است. از سيمان پرتلند تيپ 2و مصالح سنگي سيليسي درشت دانه با اندازه بزرگترين دانه برابر با 19/5ميليمتر و ماسه اصلاح شده در دسترس براي ساخت بتن استفاده شده است. با افزايش درصد الياف، ميزان اسلامپ، مقاومت فشاري، مقاومت خمشي بتن مورد بررسي قرار گرفته است.
مقدمه
بتن در عين دارا بودن مزيت هاي متعدد، رفتاري تردشكن دارد. بتن در نمودار تنش- كرنش داراي شيب نزولي تندي است. كاهش سريع مقاومت فشاري در ناحيه بعد از پيك بار به شكل معلومي موجب مود تردشكني گسيختگي ميشود. براي بهبود شكلپذيري بتن يك استراتژي وجود دارد و آن افزودن الياف به بتن مي باشد. تحقيقات نشان داده است افزودن الياف فولادي به بتن شكل قابل توجهي باعث افزايش مقاومت هاي خمشي و فشاري بتن ميشود. اما استفاده از الياف فولادي آماده كه در كارخانه توليد ميشود هم باعث افزايش هزينه ساخت بتن ميشود و هم اينكه هنوز اين الياف در داخل كشور توليد نميشود. از طرف ديگر در قطب هاي صنعتي كشور مقدار زيادي تراشههاي فولادي وجود دارد. در اين تحقيق با توجه به مزاياي بتن اليافي كه گفته شد تاثير استفاده از تراشههاي زائد صنعتي به عنوان الياف فولادي بازيافت شده بر روي خواص بتن مورد بررسي و پژوهش قرار مي گيرد.
ABSTRACT
Concrete is one of the most important and cheapest materials available in the world. The benefits of concrete have become the favorite of most engineers, designers and employers. The main advantages of concrete, good compressive strength, its ability to use in most geographical areas, the use of natural and cheap materials, low cost versus high volume of operation, its formation according to geometric shapes of the design, the possibility of mechanization of operations, the need for Expensive maintenance during lifetime and. . . Is. But the concrete in the stress-strain diagram has a steep descent slope. The rapid reduction of compressive strength in the area after the peak load in a definite manner results in a breakdown of the tightening mode. There is a solution to improve concrete ductility, which is the addition of fibers to concrete. The cost of producing fibers produced in the factory is high. Regarding the abundance of metallic waste found in industrial poles of the country and even in small workshops, in this study, pulp produced in welding and shear workshops as fibers for the weapon of concrete was used. In this research, spiral steel chips have been used in volumes of 0, 40, 80 and 1/2 percent. Portland cement type 2 and aggregate silica stone material with the largest grain size of 19.5 mm and modified sand available for concrete production. With increasing fiber content, slump, compressive strength, flexural strength of concrete have been investigated.
INTRODUCTION
Concrete, while possessing several advantages, has a slippery behavior. Concrete in the stress-strain diagram has a steep descent slope. The rapid reduction of compressive strength in the area after the peak load in a definite manner results in a breakdown of the tightening mode. To improve the shape of concrete, there is a strategy that add fiber to concrete. Research has shown that the addition of steel fibers to concrete significantly increases the flexural strength and compressive strength of concrete. But the use of ready-made steel fibers produced in the factory also increases the cost of manufacturing concrete, and that this fiber is still not produced in the country. On the other hand, there are a lot of steel chips in the industrial poles of the country. In this study, considering the advantages of fiber concrete, the impact of the use of industrial waste chips as recycled steel fibers on the properties of concrete is investigated.
Year: 2011
Publisher : Sixth National Congress on Civil Engineering
By : Mohammad Hossein Modaresi , Hossein Rahnama , Ali Lashkari
File Information: English Language/ 8 Page / size: 360 KB
Only site members can download free of charge after registering and adding to the cart
سال : 1390
ناشر : ششمین کنـگره ملی مهنـدسی عمـران
کاری از : محمد حسين مدرسي ، حسين رهنما ، علي لشكري
اطلاعات فایل : زبان فارسی / 8 صفحه / حجم : KB 360
نقد و بررسیها
هنوز بررسیای ثبت نشده است.