توضیحات
چکیده
در اين تحقيق به بررسي تاثير مقدار و اندازه ذرات جوانه زاي پيشنهادي Ti-6Al-4Vپرداخته شد. جوانه زای Ti-Al-Vاز تبديل تراشه هاي ماشينکاری پروتزهاي آلياژ بيومتريال Ti-6Al-4Vبه پودر (با استفاده از دستگاه اتمايزر) با مش هاي 60 ، 30و 100تهيه شد و در سه مقدار 0/2 ، 0/1 و 0/5درصد وزنی و جوانه زاي متعارف Al-Ti-Bنيز درهمين مقادير و در شرايط يکسان به مذاب آلياژ آلومينيوم A356افزوده شد. آزمايشات متالوگرافی جهت بررسی ريزساختار و اندازه گيری فاصله بين بازوهای دندريتی (DAS) انجام گرفت. نتايج به دست آمده نشان داد جوانه زای Ti-Al-Vمقدار DASرا نسبت به جوانه زای رايج در صنعت آلومينيوم (Al-Ti-B) به ميزان زيادی کاهش داده و در بهترين حالت DASرا به 44ميکرون می رساند. عامل اصلی جوانه نی فاز TiAl3است که با ايجاد فصل مشترک شبه همسيما و از طرفی با تشکيل محصول واکنش پريتکتيکی( L+TiAl3→Solid (α-Alسبب فراهم آمدن مکانهای مناسب جوانه زنی دندريتهای اوليه آلومينيوم می گردد.
مقدمه
از اساسي ترين مباحث تحقيق در علم مواد، ارتباط خواص مکانيکي مواد با ساختار دروني آنها مي باشد. به منظور دستيابي به مشخصات متالورژيکي و اقتصادي مطلوب، ايجاد ساختاري يکنواخت به عنوان انگيزه اي مهم در توليد شمشها و قطعات ريختگي ضروري به نظر مي رسد. از مهم ترين عوامل کاهش خواص مکانيکي و تضعيف قابليت کارپذيري قطعه، دانه بندي درشت، بالا بودن مقدار DASو غيريکنواخت بودن ساختار مي باشد، زيرا اين گونه دانه بندي توزيع عناصر محلول جامد و فازهاي ثانويه و… را در دامنة انجماد و عمليات حرارتي و يکنواخت سازي ساختار، تحت تأثير قرار مي دهد. مناسب ترين ريزساختار جهت رسيدن به کيفيت متالورژيکي مطلوب و در نهايت خواص مکانيکي بالا، ساختار ريز دانه با مقدار DASپايين و دانه بندي هم محور مي باشد که بهترين روش براي حصول چنين ساختاري افزودن مواد جوانه زا به مذاب مي باشد و راه هاي ديگر معمولاً به نوع قطعه، ترکيب آلياژ و شرايط ويژه ريخته گري بستگي دارند و تغيير آنها به دلخواه ميسر نيست. جوانه زای رايج در صنعت ريخته گری آلومينيوم ALB2 ,ZrC ,TiN , TiC ,Al-Ti , Al-Ti-B می باشد.
ABSTRACT
In this research, the effect of the proposed amount of germination particles Ti-6Al-4V was investigated. The Ti-Al-V germinator was prepared from the transformation of the machining chips of the Ti-6Al-4V biometric alloy prostheses into a powder (using an atomizer) with 60, 30 and 100 meshes and in three concentrations of 0.2, 0.1 and 0.5 percent Al-Ti-B conventional algae and algae were added to the same amount of molten aluminum alloy A356 under the same conditions. Metallographic experiments were conducted to investigate the microstructure and measure the distance between the dendritic arms (DAS). The results showed that the Ti-Al-V germination significantly reduced the DAS content compared to the conventional Al-Ti-B germination, and, at best, reduced the DAS to 44 microns. The main factor of the TiAl3 reagent is the formation of a quaternary coexistence and, on the other hand, the formation of the product of the reactive process (L + TiAl3 → Solid (α-Al)) provides suitable sites for the germination of primary aluminum dendrites.
INTRODUCTION
One of the most important issues in research in materials science is the relationship between the mechanical properties of materials and their internal structure. In order to achieve the desired metallurgical and economical characteristics, creating a uniform structure as an important motive for the production of ingots and casting parts is necessary. One of the most important factors in reducing the mechanical properties and weakening of the unit’s capability, large granularity, high DAS and non-uniformity of the structure, because this gradation of the distribution of solids and secondary phases, etc. in the range of freezing and heat treatment And uniformity of the structure affects. The most suitable microstructure is to achieve the desired metallurgical quality, and finally, high mechanical properties, a fine grain DAS structure and a co-axial graining, the best method for obtaining such a structure is the addition of germinating materials to the molten, and other ways are usually The type of alloy, the alloy composition, and the special casting conditions depend on the desired variation. The most commonly used germination in the aluminum casting industry is ALB2, ZrC, TiN, TiC, Al-Ti, Al-Ti-B.
Year: 2017
Publisher : 11th National Congress of metallurgy of Iran
By : Vahab Jamali, Hamed Tamizifar, Niko Nazifkar, Morteza Tamiyazifar
File Information: persian Language/ 11 Page / size: 1,90 KB
Only site members can download free of charge after registering and adding to the cart
سال : 1396
ناشر : يازدهمين كنگره ملي مهندسين متالورژی ايران
کاری از : وهاب جمالي ,حامد تميزی فر, نيکو نظيفکار , مرتضي تميزي فر
اطلاعات فایل : زبان فارسی / 11 صفحه / حجم : KB 1,90
نقد و بررسیها
هنوز بررسیای ثبت نشده است.