توضیحات
چکیده
SAMDروش نسبتا جديدي در توليد پودرهاي فلزي است كه در آن از هم پاشيدگي و تكه تكه شدن مذاب، در اثر همزدن مذاب به همراه يك ماده واسط جامد صورت ميپذيرد و پس از انجماد قطرات مذاب حاصل و جدا نمودن ماده واسط، پودر فلزي به دست ميآيد. در تحقيق حاضر، پودر آلياژ Al 6- wt%Siبا استفاده از اين روش توليد شده و تاثير برخي از پارامترهاي فرآيند از قبيل نوع ماده جامد واسط (آلومينا و يا نمك طعام)، نسبت وزني ماده واسط به آلومينيم و سرعت همزدن بر اندازه و مورفولوژي پودر حاصله مورد بررسي قرار گرفته است. نتايج نشان ميدهد كه در تهيه پودر آلومينيم به روش SAMDبه وسيله نمك طعام، حداقل اندازه متوسط ذرات در دور همزن 1400rpmو نسبت وزني NaClه ب Alبرابر با به 4دست ميآيد. مطالعات ميكروسكوپ الكتروني روبشي (SEM) نشان ميدهد كه مورفولوژي پودرها به شكل كروي بوده و اساسا به رژيم دما – زمان مورد استفاده بستگي دارد و پارامترهاي ديگر مثل سرعت همزدن و نسبت وزني NaClبه Alروي اين مورفولوژي تاثير بسزايي ندارند، ولي در نسبت هاي كم نمك به آلومينيم به دليل انجماد زودرس، برخي از قطرات كوچك به شكلهاي نامنظم منجمد ميشوند.
مقدمه
از مهمترين روشهاي توليد پودر فلزات كه از لحاظ اقتصادي قابل استفاده هستند ميتوان به روشهاي مكانيكي، شيميايي، الكتروشيميايي و اتمايزينگ اشاره نمود. روشهاي اتمايزينگ داراي انواع مختلفي از قبيل اتمايزينگ دو سياله (Twin fluid atomization) و گريز از مركز هستند كه در آنها، جرياني از فلز مذاب با اعمال انرژي، به قطرات بسيار كوچك مذاب تبديل شده كه پس از انجماد پودر فلزي حاصل ميشود. در تكنيك اتمايزينگ دو سياله، تكه تكه شدن مذاب به وسيله اصابت مستقيم جت يك سيال ديگر مثل يك گاز تحت فشار(هوا، نيتروژن، آرگون، هليم)، بخار آب، روغن و ا آب به- دست ميآيد. از ديگر روشهاي تهيه پودر كه در آن توزيع مناسبي از اكسيد فلز به عنوان استحكام دهنده حاصل ميشود، روش آلياژسازي كانيكي ميباشد كه در اين فرآيند، پودرها مرتبا در محفظه آسيا، جوش خورده، شكسته شده و دوباره جوش ميخورند. در ميان روشهاي وليد پودر ذكر شده، روش اتمايزينگ به طور گستردهاي مورد استفاده قرار گرفته است.
ABSTRACT
SAMD is a relatively new method in the production of metal powders, in which the disintegration and fragmentation of the melt is accomplished by mixing the melt with a solid intermediate material, and after the freezing of the molten droplets and the separation of the intermediate material, a metal powder is obtained . In the present study, Al 6 wt% Si alloy powder was produced using this method and the effect of some process parameters such as the type of solid material (alumina or salt), the weight ratio of the medium to aluminum, and the rate of stirring on the size and The morphology of the resulting powder has been studied. The results show that in the preparation of SAMD aluminum powder by salt water, the minimum average particle size in the stirring round is 1400 rpm and the NaCl ratio is equal to 4 times. Scanning Electron Microscopy (SEM) studies indicate that the morphology of the powder is spherical and essentially depends on the temperature-time regime used, and other parameters such as stirring rate and NaCl to Al ratio do not affect this morphology, but in low salt ratios To aluminum due to early freezing, some small droplets are frozen in irregular shapes.
INTRODUCTION
Mechanical, chemical, electrochemical, and atomization methods are one of the most important methods of metal powder production that can be used economically. Otmizing methods have different types, such as twin fluid atomization and centrifugal extinction, in which the flow of molten metal by energy is converted into very small droplets of molten metal which is obtained after freezing of the metal powder. In the two-syllable metamaterial technique, the fragmentation of the melt is achieved by direct jet-loading of another fluid, such as a pressurized gas (air, nitrogen, argon, helium), water vapor, oil, and water. Other powder preparation methods, in which a suitable distribution of metal oxide as a stabilizer is obtained, is a cannical alloying process. In this process, the powders are constantly welded, broken, and re-boiled in an Asian chamber. Among the methods described in Waleed Powder, the method of metamorphism is widely used.
Year: 2007
Publisher : 11th National Congress of metallurgy of Iran
By : Pooya Delshad Khatibi, Farshad Akhlaghi
File Information: persian Language/ 10 Page / size: 988 KB
سال : 1386
ناشر : يازدهمين كنگره ملي مهندسين متالورژی ايران
کاری از : پويا دلشاد خطيبي ، فرشاد اخلاقي
اطلاعات فایل : زبان فارسی / 10صفحه / حجم : KB 988
نقد و بررسیها
هنوز بررسیای ثبت نشده است.