توضیحات
ABSTRACT
A Power quality problem is an occurrence manifested as a nonstandard voltage, current or frequency that results in a failure or a mis-operation of end user equipments. Utility distribution networks, sensitive industrial loads and critical commercial operations suffer from various types of outages and service interruptions which can cost significant financial losses. With the restructuring of power systems and with shifting trend towards distributed and dispersed generation, the issue of power quality is going to take newer dimensions. In developing countries like India, where the variation of power frequency and many such other determinants of power quality are themselves a serious question, it is very vital to take positive steps in this direction .The present work is to identify the prominent concerns in this area and hence the measures that can enhance the quality of the power are recommended .This work describes the techniques of correcting the supply voltage sag, swell and interruption in a distributed system. At present, a wide range of very flexible controllers, which capitalize on newly available power electronics components, are emerging for custom power applications. Among these, the distribution static compensator and the dynamic voltage restorer are most effective devices, both of them based on the VSC principle. A DVR injects a voltage in series with the system voltage and a D-STATCOM injects a current into the system to correct the voltage sag, swell and interruption. Comprehensive results are presented to assess the performance of each device as a potential custom power solution .
INTRODUCTION
One of the most common power quality problems today is voltage dips. A voltage dip is a short time (10 ms to 1 minute) event during which a reduction in r.m.s voltage magnitude occurs. It is often set only by two parameters, depth/magnitude and duration. The voltage dip magnitude is ranged from 10% to 90% of nominal voltage (which corresponds to 90% to 10% remaining voltage) and with a duration from half a cycle to 1 min. In a three-phase system a voltage dip is by nature a threephase phenomenon, which affects both the phase-toground and phase-to-phase voltages. A voltage dip is caused by a fault in the utility system, a fault within the customer’s facility or a large increase of the load current, like starting a motor or transformer energizing. Typical faults are single-phase or multiple-phase short circuits, which leads to high currents. The high current results in a voltage drop over the network impedance. At the fault location the voltage in the faulted phases drops close to zero, whereas in the non-faulted phases it remains more or less unchanged.
چکیده
یک مشکل کیفیت برق یک رخداد است که به عنوان یک ولتاژ، جریان یا فرکانس غيرمتعارف مشهود است که موجب خرابی یا عدم استفاده از تجهیزات کاربر نهایی می شود. شبکه های توزیع سودمند، بارهای صنعتی حساس و عملیات تجاری بحرانی از انواع مختلف قطع و قطع خدمات می توانند هزینه های قابل توجهی را متحمل شوند. با بازسازی سیستم های قدرت و با روند تغییر جهت نسل توزیع شده و پراکنده، مسئله کیفیت قدرت، ابعاد جدیدتری را به خود اختصاص می دهد. در کشورهای در حال توسعه مانند هند، جایی که تغییر فرکانس قدرت و بسیاری از عوامل دیگر کیفیت قدرت، خودشان یک سوال جدی هستند، بسیار مهم است که گام های مثبتی در این زمینه بگیریم. کار حاضر این است که نگرانی های برجسته در این زمینه را شناسایی کنیم و از این رو توصیه می شود که اقداماتی که می توانند کیفیت قدرت را افزایش دهند توصیه می شود. این کار تکنیک های اصلاح ولتاژ تغذیه، تورم و وقفه در یک سیستم توزیع را توصیف می کند. در حال حاضر، طیف گسترده ای از کنترل های بسیار انعطاف پذیر، که بر روی اجزای الکترونیکی الکترونیک قدرتمند جدید سرمایه گذاری می کنند، برای برنامه های قدرت سفارشی ظاهر می شوند. در میان این، جبران کننده استاتیک توزیع و ترمیم کننده ولتاژ پویا موثرترین دستگاه هستند، هر دو آنها بر اساس اصل VSC است. DVR یک سری ولتاژ را با ولتاژ سیستم تزریق می کند و D-STATCOM یک جریان را به سیستم تزریق می کند تا ولتاژ ولتاژ، تورم و وقفه را اصلاح کند. نتایج جامع ارائه شده برای ارزیابی عملکرد هر دستگاه به عنوان یک راه حل قدرت بالقوه سفارشی است.
مقدمه
یکی از شایع ترین مشکلات کیفیت قدرت امروز ولتاژ است. یک شیب ولتاژ یک زمان کوتاه (10 تا 1 دقیقه) است که در طی آن کاهش ولتاژ r.m.s مقدار رخ می دهد. این اغلب تنها با دو پارامتر، عمق / اندازه و مدت زمان تعیین می شود. ولتاژ شیب ولتاژ 10 تا 90 درصد ولتاژ اسمی (که مربوط به 90 تا 10 درصد ولتاژ باقی مانده است) و با مدت زمان نیمی از چرخه تا 1 دقیقه متغیر است. در یک سیستم سه فاز یک شیب ولتاژ به صورت طبیعی یک پدیده سه فاز است که بر روی ولتاژ فاز به زمین و فاز تا فاز تأثیر می گذارد. افت ولتاژ ناشی از خطا در سیستم ابزار، خطا در تسهیلات مشتری یا افزایش بزرگ جریان بار، مانند شروع یک موتور یا ترانسفورماتور انرژی است. گسل های معمولی مدارهای کوتاه تک فاز یا چند فازی هستند که منجر به جریان زیاد می شود. جریان بالا موجب افت ولتاژ بر امپدانس شبکه می شود. در محل گسل ولتاژ در فازهای ناپدید می شود نزدیک به صفر، در حالی که در فاز غیر غلبه آن بیشتر یا کمتر بدون تغییر باقی می ماند.
Year: 2007
Publisher : IEEE
By : S.V Ravi Kumar and S. Siva Nagaraju
File Information: English Language/ 7 Page / size: 274 KB
Only site members can download free of charge after registering and adding to the cart
سال : 1386
ناشر : IEEE
کاری از : S.V Ravi Kumar و S.Siva Nagaraju
اطلاعات فایل : زبان انگلیسی / 7صفحه / حجم : KB 274
نقد و بررسیها
هنوز بررسیای ثبت نشده است.