توضیحات
چکیده
اخيرا روش طراحي سيستم هاي راهگاهي توسط پروفسور J. Campbellبر اساس سـالها مشـاهده نحـوه پـر شـدن قالـب توسط دستگاه اشعه ايكس به طور كلي دگرگون شده است. روش پيشنهادي او نه بر اساس نسبت سيستم راهگاهي، بلكه بر اساس طبيعت حركت مذاب و مفهوم سرعت بحراني مـذاب اسـتوار اسـت. در سيسـتم راهگـاهي جديـد (طبيعـي-فشـاري) مفهوم تنگه موضعي به كلي حذف شده و تمام سيستم به صورت يك تنگه سراسـري عمـل ميكنـد. در هـر حـال تـا كنـون تحقيقات كمي در مورد تفاوتهاي اين سيستم با سيستم راهگـاهي متـداول غيـر فشـاري از نظـر خـواص مكـانيكي و قابليـت اعتماد به قطعه انجام شده است. در پژوهش حاضر قطعاتي استوانه اي شكل توسط هر دو سيستم توسط مذاب آليـاژ A356 آلومينيم ريخته شده و استحكام كششي و درصد ازدياد طول نسـبي آنهـا توسـط روش آمـاري Weibullمـورد تجزيـه و تحليل قرار گرفته است. علاوه بر آن تاثير وجود فيلتر سراميكي بـر خـواص مكـانيكي قطعـات توليـد شـده توسـط سيسـتم طبيعي-فشاري نيز مورد بررسي قرار گرفت. نتايج نشان ميدهند كه قطعات توليد شده توسط سيستم طبيعي-فشـاري عليـرغم داشتن خواص يكسان، داراي قابليت اعتماد به قطعه بالاتري نسبت به قطعات توليد شده توسط سيسـتم غيـر فشـاري هسـتند. همچنين نشان داده شد كه تاثير استفاده از سيستم راهگاهي طبيعي ف- شاري در افزايش قابليت اعتماد به قطعه از تـاثير وجـود فيلتر اسفنجي در سيستم غير فشاري بيشتر است.
مقدمه
وارد شدن مذاب به درون حفره قالب يكي از پر تلاطم ترين فراينـدها در خـلال ريختـه گـري يـك قطعـه بـه شـمار ميـرود. Campbellتاثير طراحي سيستم راهگاهي بر توليد عيوب اكسيد فيلم دوتائي در حين بارريزي قطعه را توسط دسـتگاه اشعه ايكس و نرم افزارهاي شبيه سازي جريان سيال مورد بررسي قرار داده است. تصاوير اشعه ايكس به روشني نشان دادنـد كه تقريبا تمام سيستم هاي راهگاهي كه تا آن موقع به عنوان سيستم هاي راهگاهي “خوب” شناخته ميشدند همگـي باعـث توليد مقدار بسيار زيادي عيب اكسيد دوتائي در حين بارريزي ميگرديدند. كمپبـل بـر اسـاس ايـن مشـاهدات و همچنـين بـا توجه به مفهوم سرعت بحراني مذاب، نحـوه طراحـي بسـياري از قسـمتهاي سيسـتم راهگـاهي را دگرگـون نمـود و طراحـي سيستم راهگاهي را به طور كلي بر اساس اصول جديدي بنيان نهاد.
ABSTRACT
Recently, the method of designing systems by Prof. J. Campbell has been based on years of observation of how the template is filled up by the X-ray machine in general. His proposed method is based not on the ratio of the propulsion system, but on the basis of the nature of the molten motion and the concept of critical melt velocity. In the new (natural-compressive) gangway system, the concept of the Strait is completely eliminated and the whole system acts as a Strait. However, so far, little research has been carried out on the differences between the system and the non-compression routing system in terms of mechanical properties and reliability of the parts. In the present study, cylindrical shaped parts were cast by aluminum alloy A356 alloy with both systems, and the tensile strength and relative elongation percent were analyzed by Weibull statistical method. In addition, the effect of the ceramic filter on the mechanical properties of components produced by the natural-compression system was also studied. The results show that the components produced by the natural-compression system, despite having the same properties, have higher reliability to components than those produced by the non-compression system. It was also shown that the effect of the use of a natural farkar landing system on increasing the reliability of the piece is greater than the effect of the presence of sponge filter in the non-compression system.
INTRODUCTION
The introduction of molten into the mold cavity is one of the most turbulent processes during the casting of a piece. Campbell examines the effect of designing a system for the production of binary oxide defects during fragmentation by X-ray machine and fluid flow simulation software. X-ray images clearly showed that almost all of the landing systems that until then were known as “good” launch systems all produced a huge amount of binary oxide defects during the booty. Based on these observations, and based on the concept of critical melt speed, Campbell changed the design of many parts of the system, and based the design of the marching system on the basis of new principles.
Year: 2007
Publisher : The 19th Seminar of the Iranian Scientific Casting Association
By : Hatef Hashemi, Mahdiyeh Mashayekhi, Nafiseh Hamidi, Ramin Rayszadeh
File Information: persian Language/ 10 Page / size: 1.16 KB
سال : 1386
ناشر : نوزدهمين سمينار انجمن علمي ريخته گري ايران
کاری از : هاتف هاشمي ، مهديه مشايخي ، نفيسه حميدي ، رامين رئيس زاده
اطلاعات فایل : زبان فارسی / 10 صفحه / حجم : KB 1.16
نقد و بررسیها
هنوز بررسیای ثبت نشده است.