توضیحات
چکیده
در اين مقاله مرحله خشن كاري خط نورد ميلگرد فولادهاي ساختماني كارخانه كوثر گروه ملی صنعتي فولاد ايران از جنبه هاي مكانيكي و حرارتي شبيه سازي و تحليل شد.بدین منظور از نرم افزار المان محدود ABAQUS 6.5استفاده شده و نتايج بدست آمده با اطلاعات دمايي اندازه گیري شده در خط فوق و نيز نتايج تجربي ديگر محققان مقايسه گرديد. اين مقايسه توافق خوبی بين نتايج حاصل از شبيه سازي با نتايج تجربي نشان داده است. توزيع تنش در منطقه تغيير فرم و نيز توزيع درجه حرارت در منطقه تغيير فرم و بين دو پاس مورد بحث و بررسي قرار گرفته است.
مقدمه
به دليل روابط پيچيده حاكم بين متغيرهاي فرآيندهاي شكل دهي فلزات، عموما” طراحي و ارزيابي آن ها به صورت سنتي بر اساس روش هاي تجربي و عملي انجام ميشـده اسـت. از آنجـا كـه ايـن روش هـا بسـيار زمان بر و پرهزينه مي باشند، در سال های اخیر شبيه سازي عددي در فرآينـد هـاي شـكل دهـي بـه سـرعت تبديل به ابزاري مهم و كارا بـراي طراحـي و بهبـود خـواص محصـولات شـده انـد. پـيش بينـي دقيـق ابعـاد وخواص محصول در فرآيند نورد داغ ميلگرد، مسـتلزم مـدل سـازي متغیرهـاي مـؤثر شـكل دهـي و رفتـار مكانيكي ماده همچون كرنش پلاستيك، تنش و نحوه توزيع دما ميباشد. اين متغيرها بـه نوبـه خـود بـراي پيش بيني خواص و ساختار ميكروسكوپي نهايي ضروری می باشند. در گذشته تحقيقات زیادی در زمينه شبيه سازي فرآيند نورد انجام شده است، اما بيشتر اين تحقيقات در مورد ورق و يا بيلت بوده اند. از آنجا كه مطالعات كمي برروي نورد مقاطعي مانند ميلگرد انجام شده است، تحقيقات بيشتر در مورد شبيه سازي پارامترهاي مؤثر در فرآيند نورد مقطع، براي كنترل تغيير فرم و خواص نهايي محصول ضروري است. در كار حاضر فرآيند نورد مقطع ميلگرد از جنبه های حرارتي و مكانيكي به روش المان محدود و با استفاده از نرم افزار ABAQUSشبيه سازي شده است. مدل كوپله توسعه داده شده در مقياس سه بعدي قادر است نحوه توزيع حرارت، تنش و نيز كرنش در فلز و در توالي های مختلف را ارزيابي نموده و از اين طريق امكان آناليز فرآيند و بررسي ميزان تأثير متغيرهاي مختلف را ميسر سازد.
ABSTRACT
In this article, the rough work of the rolling mill roll of the steel structures of the Kavars factory of Iran’s National Steel Industrial Group was simulated and analyzed from the mechanical and thermal aspects. For this purpose, ABAQUS 6.5 limited software was used and the results were obtained with the temperature data of the measurements In the above line, as well as other empirical results, the researchers were compared. This comparison has shown a good agreement between the results of the simulation and experimental results. Distribution of stress in the region of change and the distribution of temperature in the region of change of form and between two passes have been discussed.
INTRODUCTION
Due to the complicated relations between the variables of the metal forming processes, their design and evaluation was traditionally carried out on the basis of experimental and practical methods. Since these methods are time-consuming and costly, in years Recently, numerical simulation in shaping processes has quickly become an important and effective tool for designing and improving product properties. Precise prediction of the dimensions and properties of the product in the hot rolling process involves the modeling of the effective variables of forming and mechanical behavior of the material such as Plastic strain, stress and temperature distribution. These variables are In turn, it is necessary to predict the properties and the final microscopic structure. In the past, there has been a lot of research in the field of rolling process simulation, but most of the research has been on sheet or billets. Because quantitative studies on rolling sections such as Milling has been done, further research is required on simulating the effective parameters in the rolling process of the section, to control the shape variation and final properties of the product. In the present work, the rolling process of the cross section of the thermal and mechanical aspects of finite element method using ABAQUS software is simulated. The Kolla model developed on a three-dimensional scale can evaluate the distribution of heat, stress and strain in metal in different sequences, allowing the process analysis and the effect of different variables to be analyzed.
Year: 2007
Publisher : 11th National Congress of metallurgy of Iran
By : Siamak Gharedaghi, Ahmad Kermanpour, Saeed Ziaeirad, Kourosh Hasanpour, Mahmoud Zaker
File Information: persian Language/ 10 Page / size: 315 KB
سال : 1386
ناشر : يازدهمين كنگره ملي مهندسين متالورژی ايران
کاری از : سيامك قره داغي, احمد كرمانپور , سعيد ضيايي راد, كوروش حسن پور, محمود ذاكر
اطلاعات فایل : زبان فارسی / 10صفحه / حجم : KB 315
نقد و بررسیها
هنوز بررسیای ثبت نشده است.