توضیحات
خلاصه
در اين تحقيق، آزمايش هاي برش ساده تناوبي به منظور ارزيابي پتانسيل روانگرايي ماسه ي فيروزكوه انجام گرفت. آزمايشات بر روي نمونه هاي استوانه اي به قطر 70و ارتفاع 22ميليمتر تحت شرايط بار ثابت انجام گرفته است. ساخت نمونه ها به روش كوبش مرطوب ودر يك لايه انجام گرديده است و چگالي نسبي پس از تحكيم نمونه هاي ماسه اي %75 ، %35و %55بوده است . نمونه ها تحت تنش موثر 100كيلو پاسكال تحكيم يافته اند. همه ي آزمايش ها تحت شرايط كنترل تنش برشي و با بارگذاري سينوسي انجام گرفته است. فركانس اعمال بار برشي 5/0هرتز بوده است. براي آناليز داده ها دو معيار خرابي روانگرايي اوليه معادل ضريب فشار آب حفره اي برابر يك،كرنش برشي دوبرابر دامنه %5) درنظر گرفته شده است . با توجه به نتايج بدست آمده از آزمايشات برش ساده معلوم گرديده است كه با اعمال تغييرات در دستگاه، ارزيابي قاوم مت روانگرايي امكان پذير ميباشد و نتايج بدست آمده با نتايج آزمايشات انجام شده با ديگر دستگاه ها همسو ميباشد و افزايش مقاومت روانگرايي با افزايش چگالي نسبي مشاهده گرديد.
مقدمه
روانگرايي يكي از مخرب ترين بلاياي طبيعي مرتبط با زلزله مي باشد كه در طول ساليان گذشته بسيار مورد توجه محققين قرار گرفته است. در هنگام زلزله، انتشار امواج برشي باعث كاهش حجم ماسه ي شل شده كه اين سبب افزايش فشار آب منفذي ميگردد. از آنجايي كه تكانهاي لرزه اي خيلي سريع رخ ميدهند، خاك غيرچسبنده، تحت بارگذاري زهكشي نشده قرار مي . گيرد افزايش فشار آب منفذي سبب ميشود كه آب رو به بالا به سوي سطح زمين جريان يابد، كه به صورت فواره ای از گل يا جوشش ماسه در سطح زمين ظاهر ميشود. ايجاد فشارهاي بالاي آب منفذي در اثر تكان هاي زمين و جريان رو به بالاي آب ممكن ا كند ست ماسه را به حالت روان شده تبديل كه به آن روانگرايي گفته ميشود(Day 2002). از سال 1964به علت وقوع روانگرايي در زلزله هاي نيگاتاي ژاپن مكانيزم روانگرايي و شرايط مستعد خاك براي وقوع روانگرايي تحقيقات بسياري صورت گرفت. افزايش دقت در شناخت اين پديده و پارامتر هاي موثر در وقوع آن مي تواند به كاهش هزينه ساخت انواع سازه ورسيدن به درجات بالاتري از طراحي ايمن سازه ها منجر شود.
ABSTRACT
In this research, simple periodic shear tests were conducted to evaluate the smelting potential of Firouzkooh sand. Experiments were carried out on cylindrical specimens with a diameter of 70 and a height of 22 mm under constant loading conditions. The construction of samples was carried out using a wet knocking method in a single layer, and the relative density after consolidation of sand samples was 75%, 35% and 55% respectively. The samples have been consolidated under the effective stress of 100 kPa. All experiments were conducted under conditions of shear stress control and with sinusoidal loading. The cutting load frequency was 0.5 Hz. For data analysis, the two primary creep failure criteria are equal to the cavity water pressure coefficient of one, shear strain is doubled in the range of 5%. Regarding the results of simple shear tests, it has been found that by making changes in the device, the evaluation of the continuous melting liquor is possible and the results are consistent with the results of the experiments carried out with other devices and increasing the liquefaction resistance by increasing the relative density It was observed.
INTRODUCTION
Liquefaction is one of the most devastating natural disasters associated with the earthquake, which has attracted many researchers over the past years. In the event of an earthquake, shear wave propagation reduces the amount of loose sand, which increases the pore pressure of the water. Since seismic shocks occur very quickly, non-contiguous soil is placed under unloaded drainage. Increasing the pressure of the pore water causes the water to flow up to the surface of the earth, which appears as a fountain of mud or sandburst on the surface of the earth. The formation of high vapor pressure above ground water and upward flow of water can turn the sand into a flowing state, called liquefaction (Day 2002). Since 1964, due to the occurrence of liquefaction in Japan’s Niigata earthquakes, a mechanism of liquefaction and soil susceptibility to liquefaction have been carried out. Increasing the accuracy in recognizing this phenomenon and effective parameters in its occurrence can lead to a reduction in the cost of constructing various types of structures and attaining higher levels of safety design of structures.
Year: 2011
Publisher : Sixth National Congress on Civil Engineering
By : Mohammad Mahdi Ahmadi , Athena Shirasb
File Information: English Language/ 8 Page / size: 1,449 KB
Only site members can download free of charge after registering and adding to the cart
سال : 1390
ناشر : ششمین کنـگره ملی مهنـدسی عمـران
کاری از : محمد مهدي احمدي ، آتنا شيراسب
اطلاعات فایل : زبان فارسی / 8 صفحه / حجم : KB 1,449
نقد و بررسیها
هنوز بررسیای ثبت نشده است.