توضیحات
چکیده
با توجه به استفاده گسترده فولادهاي فريتي-پرليتي در كاربردهاي صنعتي، بهينه سازي خواص آنها يكي از موضوعات مهم تحقيقات انجام شده مي باشد. بر اين اساس بهبود ريز ساختار نهايي آنها كه منجر به افزايش خواص مكانيكي مي گردد، ضروري است. اين مهم با طراحي مناسب يك مليات ترمومكانيكي امكان پذير است. در اين راستا يك پروسه ترمومكانيكي در دماي پايين شامل كار سرد و آنيل بعدي بر روي يك فولاد ساده كربني انجام شد. نمونه ها تحت كرنش هاي مختلفي در دماي اتاق قرار گرفتند ، سپس در دماهاي 725 οCو 775 οCبه مدت زمانهاي ، 120 10و 00ثانيه آنيل شده ودر نهايت به سرعت در آب سرد شدند. ريز ساختار نهايي آنها با استفاده از ميكروسكوپ نوري مورد بررسي قرار گرفت.
مقدمه
از آنجائي كه فولادهاي ساده كربني از پر مصرف ترين آلياژهاي فولادي در سازه هاي صنعتي ميباشند كار بر روي بهينه سازي خواص آنها بدون افزايش عناصر آلياژي بيشتر همواره مد نظر محققين بوده است . بر اين اساس تغيير وكنترل ريز ساختار مورد توجه قرار گرفته است. براي مثال مطالعات قبل به خوبي اثبات كرده اند كه حصول فريت چند وجهي ريز دانه با كنترل پارامترهاي مختلف ترمومكانيكي، افزايش همزمان استحكام و چقرمگي را به همراه داشته است. با كاهش هرچه بيشتر اندازه دانه هاي فريت وجزاير پرليتي ، ريز ساختاري با خواص مكانيكي مطلوبتر حاصل مي گردد. تاکنون تحقيقات بسياري بر روي حصول فريت هاي فوق ظريف منتج از پديده تغيير حالت القاء شده توسط كرنش انجام گرفته است. در اين مقاله اثر كار سرد و آنيل نهايي ساختار فريتي پرليتي بر روي ريز ساختار و اندازه دانه آن مورد بحث قرار گرفته است. تغيير شكل اين ساختار در دماي محيط ، سبب كشيده شدن دانه هاي فريت وكولوني هاي پرليت و تجمع انرژي كرنشي گرديده و موجب ايجاد مكان هاي مرجح جوانه زني شده و در نهايت ضمن انجام فرآيند آنيل ، امكان تشكيل دانه هاي جديد وظريف فريت به وجود مي آيد. همچنين در ضمن فرآيند آنيل پرليت اوليه به آستنيت و فريت پريوتكتوئيد تبديل گرديده كه ضمن سرمايش بعدي آستنيت ، مارتنزيت حاصل مي شود. بدين ترتيب مي توان به يك ريز ساختار همگن وريز دانه دست يافت.
ABSTRACT
Due to the widespread use of ferrite-perlite steel in industrial applications, optimization of their properties is one of the important research topics. Accordingly, the improvement of their final microstructure, which leads to an increase in mechanical properties, is necessary. This is possible with the proper design of a thermomechanical nation. In this regard, a thermosetting process at low temperature including cold work and subsequent annealing on a simple carbon steel was performed. The samples were placed under different strain at room temperature, then annealed at an ambient temperature of 725 ° C and 775 ° for annealing time of 120, 10, 120, and finally quickly cooled in water. Their final microstructure was studied using an optical microscope.
INTRODUCTION
Since simple carbon steel is one of the most consumable steel alloys in industrial structures, the work on optimizing their properties without increasing the alloying elements has always been considered by the researchers. Accordingly, microstructure change and control are considered. For example, previous studies have clearly demonstrated that the acquisition of multifaceted multifaceted grain with the control of various thermomechanical parameters has increased simultaneous strength and toughness. By reducing the size of the ferrite grains and the perlite grains, a microstructure with more favorable mechanical properties is obtained. So far, many studies have been carried out on the extra-fine ferrites resulting from the strain induced phenomenon. In this paper, the effect of cold and final aniline of perlite ferrite structure on microstructure and grain size is discussed. The deformation of this structure at ambient temperature causes the ferrite grains and perlite crystals to be pulled together with the accumulation of strain energy and leads to the creation of preferred germination locations. Finally, during the process of annealing, the formation of new grains and fractions can be created. . Also, during the process, the aniline perlite is transformed into austenite and perioctoid ferrite, which is followed by austenite fusion followed by martensite. In this way, a homogeneous microstructure can be obtained.
Year: 2017
Publisher : 11th National Congress of metallurgy of Iran
By : Mahdi Sabouhi, Abbas Zarei Hanzaki
File Information: persian Language/ 10 Page / size: 600 KB
سال : 1396
ناشر : يازدهمين كنگره ملي مهندسين متالوژی ايران
کاری از : مهدي صبوحي، عباس زارعي هنزكي
اطلاعات فایل : زبان فارسی / 10 صفحه / حجم : KB 600
نقد و بررسیها
هنوز بررسیای ثبت نشده است.