توضیحات
چکیده
در اين كار پژوهشي فاكتورهاي مختلف از جمله تاثير زمان آبكاري، pHحمام، ضـخامت، درصـد فسـفر موجود در پوشـش و شـرايط عمليـات حرارتـي بـر رفتـار خـوردگي الكتروشـيميايي پوششهاي آبكـاري الكترولس نيكل-فسفر مورد بررسي و با نمونه هاي مشابه از طريق خوردگي غوطه وري مقايسـه گرديـد . منحني هـا و نتـايج پارامترهـاي خـوردگي نظيـر دانسـيته جريـان خوردگي،مقاومـت پلاريزاسيون،پتانسـيل وسرعت خوردگي براي نمونه هاي بـا عمليـات حرارتـي و بـدون عمليـات حرارتـي در زمانهـاي مختلـف آبكاري از طريق منحني هاي تافل در نمونه محلول شبه آب دريا ( 5 /3% NaCl) تحـت شـرايط هـوادهي بدست آمد.ساختار و مورفولوژي سـطح ايـن پوششها نيـز توسـط طيـف پـراش اشـعه xو ميكروسـكوپ الكتروني روبشي مورد مطالعه و ارزيابي قرار گرفت.نتايج بدست آمده از رفتار خـوردگي الكتروشـيميايي و ميكروسكوپ الكتروني نشان مي دهد در نمونه هاي عمليات حرارتي شده خوردگي كاهش يافته است. همچنين در نمونه هاي عمليات حرارتي و بدون عمليات حرارتي در زمانهاي 2و 5/1ساعت آبكـاري بـه ترتيب با تركيب درصد Ni-11.1%Pو Ni-10.6%Pسرعت خـوردگي كـاهش يافتـه و در عـوض در نمونه هاي با زمانهاي 3و 5/2ساعت آبكاري به ترتيب با تركيـب درصـد Ni-9.9%Pو Ni-9.1%P خوردگي افزايش يافته و يك خوردگي در مرز مشـترك و از نـوع بـين دانـه اي مشـاهده شد. خـوردگي غوطه وري نمونه ها در مدت چهار ماه نيز مطابقت خوبي با آزمايشات الكتزوشيميايي نشان مي دهد.
مقدمه
خوردگي يكي از مهمترين عوامل استهلاك قطعات و يكي از معضلات عمده صنعت ميباشد، بطوريكـه امروزه صنايع مختلفي با آن مواجه هستند. اثرات ناشي از خوردگي شامل كاهش كيفيت ظاهري قطعـات، افــزايش هزينــه عمليــات، نيــاز جــايگزيني تجهيــزات و هزينــه نگهــداري اضــافي زيان هـايي را بــراي دستاندركاران صنايع فراهم آورده است. با توسعه پوششهاي حاصل از آبكاري بدون برق مشكل مربوط به تخلخل پوششها تا حدود زيادي بر طرف گرديده است. پوششـهاي آبكـاري بـدون بـرق نيكـل – فسـفر داراي مزيتهاي زيادي بوده از جمله مزاياي آنها مي توان به ضخامت يكنواخت، توانائي توليـد پوششـي بـا مقاومت خوردگي بالا، سختي و مقاومت سايشي مناسب و قابليت پوشش دادن اكثر مواد شامل پليمرهـا و پلاسـتيكها اشـاره كـرد. مقاومـت خـوردگي پوششـهاي مـورد نظـر را مـيتـوان بـا انتخـاب صـحيح فاكتورهايي همچون ضخامت پوشش، درصد فسفر و انتخاب صحيح حمام تغيير داد. مقدار فسـفر موجـود در پوششهاي بدون برق نيكل – فسفر در حمام اسيدي هيپوفسفيت بستگي به شيمي حمام و شـرايط كـاري آن دارد.
ABSTRACT
In this research, various factors such as the effect of electroplating, bath pH, thickness, percentage of phosphorus in coating and thermal treatment conditions on the electrochemical corrosion behavior of electrolytic nickel-phosphorous coatings were investigated and compared with similar samples by immersion corrosion. Curves and the results of corrosion parameters such as corrosion density, polarization resistance, corrosion potential and corrosion rate for heat treatment and heat treatment samples at different times of electroplating through the TOEFL curves in a sample of water-saturated solution (3.5% NaCl) Aeration conditions were obtained. The structure and surface morphology of these coatings were studied and evaluated by the X-ray diffraction spectrum and scanning electron microscopy. The results of electrochemical corrosion and electron microscopy showed that corrosion was reduced in the heat treatment samples . Also, in thermal and non-heat treatment samples at 2 and 1.5 hours of electroplating, the corrosion rate decreased with Ni-11.1% P and Ni-10.6%, respectively, and in the samples with 3 and 2.5 hours of electroplating, respectively, Ni -9.9% P and Ni-9.1% P corrosion were increased with corrosion and a cross-sectional corrosion was observed. Corrosion of specimens immersion in four months also shows a good correlation with ecochemical experiments.
INTRODUCTION
Corrosion is one of the most important factors in the depreciation of parts and is one of the main problems of the industry, so today there are various industries facing it. The effects of corrosion include reducing the apparent quality of the parts, increasing operating costs, replacing equipment, and additional maintenance costs, which has caused damage to industry players. With the development of non-electric coatings, the problem of porosity of coatings has been largely overcome. Nickel-phosphorous electroplating coatings have many advantages, including the advantages of uniform thickness, the ability to produce coating with high corrosion resistance, hardness and abrasion resistance, and the ability to cover most materials, including polymers and plastics. The corrosion resistance of the coatings can be changed by choosing the correct factors such as coating thickness, percentage of phosphorus and proper choice of bath. The amount of phosphorus in nickel-phosphorus-free coatings in the acid bath of hypophosphate depends on the chemistry of the bath and its working conditions.
Year: 2007
Publisher : 11th National Congress of metallurgy of Iran
By : Seyed Hossein Rafizadeh – Habib Ashayati Sorkhi
File Information: persian Language/ 12 Page / size: 722 KB
سال : 1386
ناشر : يازدهمين كنگره ملي مهندسين متالورژی ايران
کاری از : سيد حسين رفيع زاده -حبيب اشعثي سرخابي
اطلاعات فایل : زبان فارسی / 12 صفحه / حجم : KB 722
نقد و بررسیها
هنوز بررسیای ثبت نشده است.