توضیحات
چکیده
یکی از مشکلات موجود در طراحی پی ها مربوط به حالتی است که نیروي کششی زیادي در پاي ستون ها بوجود آید. در نرم افزار SAFE عملیات حذف فنرهاي کششی خاك بر اساس تئوري فنر ارتجاعی وینکلر و تنها براي ترکیبات بارگذاري انجام می شود. وجود کشش زیاد در پاي ستون می تواند منجر به نتایج غیر اقتصادي شود. از سوي دیگر چون عملیات تحلیل بدون لحاظ نمودن اثر میلگردهاي پی صورت می گیرد،مقطع تحلیل شده با آنچه که در نهایت به مرحله اجرا در می آید یکسان نخواهد بود. این مقاله موضوع فوق را مورد بررسی قرار می دهد.
مقدمه
یکی از مسائلی که بعضاً در طراحی فونداسیون ها به آن برخورد می شود وجود نیروي کششی بسیار زیاد در پاي ستونها است. در برخی از ترکیبات بارگذاري معرفی شده در آیین نامه ها علاوه بر کاهش و بعضاً حذف اثر بارهاي زنده و مرده، نیروي زلزله افزایش داده می شود. بنابراین بوجود آمدن نیروهاي کششی زیاد در فونداسیون ها تبدیل به موضوع مهمی در طراحی آنها شده است. هم اکنون رایج ترین نرم افزار در طراحی فونداسیون ها نرم افزار AFEمی باشد. این نرم افزار خاك زیر پی را بر اساس تئوري فنرهاي ارتجاعی وینکلر به صورت فنرهایی با رفتار خطی در نظر می گیرد و از یک عملیات تکراري به منظور حذف فنرهاي کششی استفاده می کند.در طراحی فونداسیون از بارهاي ضریبدار استفاده می شود و نرم افزار SAFEنیز عملیات حذف کشش را تنها براي ترکیبات بارگذاري انجام می دهد. در این نرم افزار براي آنالیز مدلهایی که بر روي یک بستر تکیه گاهی قرار دارند گزینه اي پیش بینی شده است که با فعال نمودن این گزینه کلیه فنرها تنها به صورت فشاري عمل خواهند کرد. در طراحی پی ها همواره باید از حالت Iterative for uplift استفاده شود. ر این حالت نرم افزار یک عملیات تکراري را جهت حذف کشش در خاك انجام می دهد . این عملیات را می توان به صورت زیر بیان کرد: ابتدا یک تحلیل عادي انجام شده و فنرهاي تحت کشش مشخص می شود. در تحلیل بعدي این فنرها حذف می شوند و مجدداً تغییرمکان ها و نتایج جدید بدست می آیند .این عملیات تکراري تا ناچیز شدن کشش ایجاد شده در تمام فنرهاي گرهی ادامه پیدا می کند.
ABSTRACT
One of the problems in the design of the pins is that there is a large tensile force at the bottom of the pillars. In the SAFE software, the pull-out of springs is performed on the basis of the Winkler Reinforced Spring theory and only for loading components. Existing tensions at the foot of the column can lead to non-economic results. On the other hand, since the analysis operation without taking into account the effect of Pyramid’s actions, the analyzed section will not be identical with what will eventually be implemented. This article discusses the above issue.
INTRODUCTION
One of the issues that is sometimes addressed in the design of the foundations is the presence of a large tensile force at the foot of the columns. In some of the loading combinations introduced in the regulations, in addition to reducing and sometimes eliminating the effects of dead and dead loads, earthquake forces are increased. Therefore, the emergence of tensile forces in foundations has become an important issue in their design. Currently, the most commonly used software for designing foundations is the AFE software. This software considers the subsoil soil based on the Vincenre elastic spring springs as linear linear springs and uses a repetitive operation to remove tension springs. In the design of the foundation, the coefficient loads are used and the SAFE software The pull-out operation only performs loading combinations. The software is designed to analyze models that are mounted on a recessed platform, which is expected to activate all the springs as a compress only. In the design of the pins, Iterative for uplift should always be used. In this mode, the software performs a repetitive operation to remove traction in the soil. This operation can be expressed as follows: First, a normal analysis is performed and the tension springs are identified. In the next analysis, these springs are removed and new displacement and new results are obtained. This repeat operation continues until the tensile tension in all nodes is maintained.
Year: 2011
Publisher : Sixth National Congress on Civil Engineering
By : Mehdi Khodaparast, Gholamreza Zar Noshah Farahani
File Information: persian Language/ 9 Page / size: 999 KB
Only site members can download free of charge after registering and adding to the cart
سال : 1390
ناشر : ششمين كنـگره ملي مهندسی عمـران
کاری از : مهدي خداپرست ،غلامرضا زرنوشه فراهانی
اطلاعات فایل : زبان فارسی / 9 صفحه / حجم : KB 999
نقد و بررسیها
هنوز بررسیای ثبت نشده است.