توضیحات
چکیده
از يك ليزر پالسي Nd:YAGبا توان متوسط پايين براي جوش ورق كم كربن استفاده شد.آزمايشات براي تعيين اثر انرژي پالس، عرض پالس و سرعت جوشكاري بر ابعاد جوش، ميكروساختار و سختي در جوشكاري ليزري پالسي فولاد كم كربن صورت گرفت. شرايط جوشكاري در حالت هاي هدايتي و سوراخ كليدي و اثرات پارامترهاي فرآيند ليزر بر آن مطالعه شد. با توان متوسط 240-220وات و قله توان 1.8 Kwيك جوش نفوذ كامل در حالت سوراخ كليدي در ورق St14به ضخامت 0.7ميليمتر ايجاد شد. مشخصه مجموع چگالي قله توان هاي موثر EPPDبراي بررسي بهتر اثر مقدار هم پوشاني پالسها تعريف شد. در جوش هايي با نفوذ كامل تغييرات كاملا مشخصي در ميكروساختار و سختي ناحيه جوش به علت انجماد سريع ديده شد.
مقدمه
با توجه به گسترش روز افزون ليزر در فرآيندهاي مواد، استفاده از ليزر در اتصالات و جوشكاري كاربرد فراواني پيدا كرده است. سرعت بالا، مصرف انرژي كم و قابليت جوشكاري با فاصله از سطح اتصال از خصوصيات اين روش است نسبت به روشهاي جوشكاري متداول است. همچنين انجماد بسيار سريع ( 100برابر،GTAW) نفوذ بسيار بالا، گرماي ورودي كم، HAZبسيار كم و گرده جوش كوچك از مزاياي جوشكاري ليزري است. انواع ليزر مورد استفاده در صنعت شامل ليزر CO2و Nd:YAGهستند كه بصورت پيوسته( CW)و پالسي (pulsed spot) عمل جوشكاري را انجام مي دهند. اما ليزرهاي پالسي Nd:YAG بدلیل نفوذ بيشتر و مصرف انرژي كمتر اخيرا بیشتر مورد استفاده قرار گرفته اند. نفوذ كامل خطي در جوشكاري ليزري پالسي از هم پوشاني جوشهاي نقطه اي ايجاد شده بدست ميآيد . مقدار هم پوشاني از رابطه زير محاسبه ميشود: Of = [1 − (V /f)/(D+ VT)] × 100 Dقطر لكه ليزر برروي قطعه، Vسرعت جوشكاري، fفركانس ليزر و Tپهناي زماني پالس است. مهمترين پارامترهاي تاثير گذار در جوشكاري ليزري پالسي انرژي پالس، پهناي زماني پالس، سرعت جوشكاري و قله توان پالس ليزر مي باشند. در مقاله حاضر در ادامه تحقيقات قبل نتایج حاصل از جوش لیزری پالسي صورت گرفته بر روي ورق نازك فولادي با معرفي يك پارامتر و مشخصه جديد بیان ميشوند. این پارامتر جديد در راستاي نشان دادن اثرات پارامترهاي فرایند بر خواص جوش بصورت واقعي تر تعريف مي گردد.
ABSTRACT
A low-power low-power laser Nd: YAG laser was used for low carbon sheet welding. The experiments were carried out to determine the pulse energy, pulse width and welding speed on the welding, microstructure and hardness dimensions of low carbon steel pulsed laser welding. The welding conditions in conduction and key hole states and the effects of laser process parameters were studied. With an average power of 240-220 W and peak power of 1.8 Kw, a full penetration boom was developed in a key hole in St14 sheet with a thickness of 0.7 mm. The total peak density property of EPPDs is defined to better determine the effect of pulse overlapping. In welds with full penetration, there were completely changes in the microstructure and hardness of the weld area due to rapid freezing.
INTRODUCTION
Due to the increasing use of lasers in materials processes, the use of lasers in joints and welds has been widely used. High speed, low energy consumption and weldability with distance from the bonding surface are the characteristics of this method compared with conventional welding methods. Also, very fast freezing (100 times, GTAW) high penetration, low input heat, very low HAZ and small weld pollen are the advantages of laser welding. Types of laser used in the industry include CO2 lasers and Nd: YAG, which continuously (CW) and pulsed spot perform welding operations. But Nd: YAG pulsed lasers have been used more recently due to their increased penetration and lower energy consumption. Full line penetration in pulsed laser welding is achieved through the overlap of generated point welds. The overlapping value is calculated from the following equation: Of = [1 – (V / f) / (D + VT)] × 100 D The diameter of the laser spot on the piece, V is the welding speed, f is the laser frequency and T is the pulse width. The most important parameters in pulse laser pulse welding, pulse width, welding speed and peak pulse laser power are. In the present paper, the results of laser pulsed laser welding on a thin sheet of steel are presented with a new parameter and a new characteristic. This new parameter is defined to show the effects of process parameters on the properties of the boiler more realistically.
Year: 2007
Publisher : 11th National Congress of metallurgy of Iran
By : Mohammad Javad Hamedi – Farshid Malek Qa’ini – Mohammad Javad Turkmani
File Information: persian Language/ 10 Page / size: 331 KB
سال : 1386
ناشر : يازدهمين كنگره ملي مهندسين متالورژی ايران
کاری از : محمد جواد حامدي -فرشيد مالك قائيني -محمد جواد تركمني
اطلاعات فایل : زبان فارسی / 10 صفحه / حجم : KB 331
نقد و بررسیها
هنوز بررسیای ثبت نشده است.