توضیحات
چکیده
لاية ضخيم فريت باريم با تركيب BaFe12O19ا با ستفاده از فرايند سل- ژل به روش چرخشي تهيه شد. سل توسط پودرهاي توزيع يافته در محلول اوليه فريت باريم تشكيل شد. ارزيابي ساختار، تركيب و خواص مغناطيسي لاية ضخيم فريت باريم توسط ، VSM ، EDX ، SEM ، XRDپذيرفتارسنج ac انجام شد. نتايج نشان داد كه مي توان پوشش فريت باريم عاري از ترك با ضخامت حدود 15 µm توليدکرد . مشخص شد حلقه هاي پسماند مغناطش براي ميدان مغناطيسي اعمالي در هر دو حالت موازي و عمودي تقري اًب يكسان بودند.
مقدمه
تکنولوژي مدارهاي مجتمع يكپارچه مايكروويو ، كاربرد هاي زيادي در بخش هاي تجاري و نظامي از قبيل ارتباطات ماهواره اي ، سيستم هاي موقعيت يابي و رادارها دارد. استفاده از مواد بالك براي تكنولوژي مدارهاي مجتمع نامناسب بوده و اعتقاد بر اين است كه استفاده از لايه هاي ضخيم براي چنين ادوات مايكروويو مناسب تر است. فريت باريم يك ماده فري مغناطيس است كه داراي ساختار مغناطيسي با پنج زير شبكه است كه در يك راستا واقع شده اند. اين ماده داراي ناهمسانگردي مغناطوكريستالي تك محوره به موازات محور cشبكه هگزاگونال میباشد. ساختار كريستالي آن را مي توان به پنج بلوك مطابق با نحوه چيدمان يون هاي اكسيژن به هم فشرده تقسيم نمود. بلوك S داراي دو لايه اكسيژن مي باشد كه يك ساختار اسپينل تشكيل مي دهند و بلوك Rبلوكي با پنج لايه اكسيژن است كه حاوي يون باريم مي باشد. لايه ضخيم فريت باريم به دليل ناهمسانگردي مغناطيسي قوي ، مقاومت ويژه بزرگ ، نفوذپذيري مغناطيسي بالا ، توزيع ميدان ناهمسانگردي مغناطيسي باريك و پايداري شيميايي ، يك ماده مناسب براي كاربردهاي مايكروويو مي باشد. لايه هاي فريت باريم را مي توان به چندين روش تهيه نمود. اپيتكسي فاز مايع داراي معايبي مانند محدوديت در انتخاب زيرلايه مي باشد. بوسيله تكنيك رسوب دهي پالسي ليزري ، لايه هاي تك كريستال فريت باريم بر روي زير لايه هاي (001) آلومينا و (111) اكسيد منيزيم رشد داده شده اند. سطح رسوب دهي محدود و نياز به توان الكتريكي بالا از معايب اين روش مي باشد. از سوي ديگر تكنيك سل- ژل بواسطه سهولت در ساخت اكسيدها ، مساحت رسوب دهي زياد ، توانايي استفاده بر روي زير لايه هاي مختلف ، كنترل تركيب شيميايي و زمان كوتاه فرايند ، در مقايسه با دو تكنيك رسوب دهي پالسي ليزري و اپيتكسي فاز مايع سودمندتر مي باشد.
ABSTRACT
A thick layer of Barium ferrite with BaFe12O19 was prepared using rotational sol-gel process. Tuberculosis was formed by the powder distributed in the primary solution of barite ferrite. The structure, composition, and magnetic properties of the barium ferrite layer were evaluated by VSM, EDX, SEM, XRD, and AC actuation. The results showed that cracked barite free coatings can be produced with a thickness of about 15 μm. It was found that magnetized waste loops for the applied magnetic field were the same in both parallel and vertical directions.
INTRODUCTION
Microwave integrated integrated circuits technology has many uses in commercial and military sectors such as satellite communications, positioning systems and radars. The use of bulk materials for integrated circuit technology is inappropriate and it is believed that the use of thick layers for such microwave devices is more appropriate. Barium ferrite is a magnetite ferromagnetic material with a magnetic structure with five subnets that are in the same direction. This material has an uniaxial magnetized crystalline anisotropy parallel to the hexagonal hexagonal hexagonal axis. Its crystalline structure can be divided into five blocks according to the layout of the ionized oxygen ions. The block S has two layers of oxygen, which is a spinel structure, and a block of R blocks with five layers of oxygen containing barium ions. Thick barium ferrite layer is a suitable material for microwave applications due to strong magnetic anisotropy, high strength, high magnetic permeability, narrow magnetic magnetic anisotropy and chemical stability. Barium ferrite layers can be prepared in several ways. The fluid phase epithets have some disadvantages, such as constraints in substrate selection. With the laser pulsed deposition technique, single-crystal barite ferrite layers are grown on alumina (001) and magnesium oxide (111) substrates. The limited sedimentation and the need for high electrical power are the disadvantages of this method. On the other hand, the sol-gel technique is more beneficial in comparison with the two techniques of laser pulsed deposition and liquid phase epithelium due to the ease of making oxides, the high depositional area, the ability to use on different substrates, control of chemical composition and short process time. Be
Year: 2007
Publisher : 11th National Congress of metallurgy of Iran
By : Ehsan Mohammad Sharifi, Ali Ghasemi
File Information: persian Language/ 10 Page / size: 538 KB
سال : 1386
ناشر : يازدهمين كنگره ملي مهندسين متالورژی ايران
کاری از : احسان محمد شريفي ، علي قاسمي
اطلاعات فایل : زبان فارسی / 10 صفحه / حجم : KB 538
نقد و بررسیها
هنوز بررسیای ثبت نشده است.