توضیحات
چکیده
فولادهاي دوفازي فريتي- مارتنزيتي، گروهي از فولادهاي كم آليـاژ بـا اسـتحكام بـالا هسـتند كـه شـكل پذیری خوبي از خود نشان داده و در هنگام كشش ، پديده نقطه تسلیم از خود بروز نداده ، رفتار پیوسته دارند. دراین پژوهش تاثير اعمال سيكل هاي مختلف عمليـات حرارتـي بـر خـواص مكـانیکی یک نـوع فـولاد دوفازي مورد بررسي قرار گرفته است.بدین منظور شمش ريختگي فولاد نایبیوم دار با هدف رسيدن بـه ساختاري كنواخت تحت عمليات حرارتي همگن سازي و نيز فورج قرار گرفـت و دمـا و درصـد قابليـت فورج پذیری بهینه تعيين شد. آزمون ديلاتومتري جهت تعيين دماهاي بحرانی فولاد مـورد بررسـي، انجـام گرفت و سپس نمونه هايي ياز ا ن فولاد به منظور دست يابي به سـاختاري دوفـازي در دماهـاي مختلـف و بـه مدت زمان هاي متفاوت ، آنیل درون بحراني شد. آزمون كشش با نرخ كرنش ثابت بـر آنهـا اعمـال شـد. همچنين ریز ساختارها توسط متالوگرافي مورد بررسي قرار گرفـت. يافتـه هـاي پـزوهش نشـان داد كـه بـا افزا ش دما آنیل و در نتيجه كسر حجمي آستنيت ( كه با ميزان مارتنزيت پس از كـوئنچ رابطـه مسـتقیم دارد) سطح استحكام بالا ميرود، در حاليكه ميزان كاهش داكتيليته كم است.
مقدمه
فولادهاي دوفازي گروه نسبتا جدیدی از فولادهاي با استحكام بالاي كم آلياژ (HSLA) میباشند كه داراي استحكام كششي و انعطاف پذیری بالا و ير ز ساختاري متشكل از حدود % – 10 30جزایر مارتنزيتي سخت توزيع شده در يك زمينه فريتي نرم مي باشد. به خاطر خواص جذاب فولادهاي دوفازي واینکه هزینه توليد آنها به طور قابل ملاحظه ای بیشتر از فولاد هاي كربني ساده نمي باشد ، استفاده از اين فولادها بسيار مورد توجه قرار گرفته است. به طور خلاصه فولادهاي دوفازي توسط حرارت دادن در منطقه بحراني دوفازي وسپس كوئنچ كردن از ناحيه آستنيت+فریت بدست میاید اما مسيرهاي فرایندی متفاوتی میتواند ريز ساخارها و خواص مكانیکی متفاوتي را توليد كند. ریزساختار دو فازي ، به واسطه سرد كردن فولاد از منطقه دوفازي با سرعتي كه به اندازه كافی برای استحاله آستنيت به مارتنزيت كافي باشد ، توليد مي گردد به همين دلیل تركيب شیمیایی این فولادها در تعیین دماهاي حرارتي مرجع و همچنين نرخ بحراني سرد كردن (سخت پذیري) براي استحاله به مارتنزيت از اهميت اساسي برخوردار است.
ABSTRACT
The ferritic-martensitic dual phase steels are a group of high-strength low-alloy steels that show good shape and exhibit continuous behavior when stretching. In this research, the effect of different cycles of heat treatment on the mechanical properties of a two-phase steel has been investigated. For this purpose, the casting steel of the nyemite steel was aimed at achieving a uniform structure under heat homogenization and forging, and the temperature and the percentage of the capability Optimal forgiveness was determined. Dilatometric test was carried out to determine the critical temperature of the steel under investigation. Then, samples of this steel were anesthetized in order to achieve a two-phase structure at different temperatures for different periods of time. The tensile test was applied to them with constant strain rate. Also, microstructures were investigated by metallography. The results showed that with increasing annealing temperature and as a result of a volume fraction of austenite (which is correlated with the amount of martensite after quenching), the strength level is high, while the ductility decrease is low.
INTRODUCTION
Double-phase steels are a relatively new high-strength, low-alloy steels (HSLA) group with high tensile strength and structural strength of about 10-30% of hardened martensitic islands distributed in a soft ferrite field. Due to the attractive properties of dual-phase steels, and the cost of their production is not significantly greater than that of carbon steel, the use of these steels is very much taken into consideration. In short, two-phase steels are obtained by heating in a two-phase critical region and then quenched from austenite + ferrite, but different process paths can produce different microstructures and mechanical properties. The two-phase microstructure is produced by cooling the steel from a two-phase zone at a speed sufficient to transform austenite to martensitic. Therefore, the chemical composition of these steels in determining the reference thermal temperatures and the critical cooling rate (hardness ) Is of paramount importance for martensite transformation.
Year: 2007
Publisher : 11th National Congress of metallurgy of Iran
By : Hamed Soleimani, Abbas Najafizadeh
File Information: persian Language/ 10 Page / size: 775 KB
سال : 1386
ناشر : يازدهمين كنگره ملي مهندسين متالورژی ايران
کاری از : حامد سليماني ،عباس نجفي زاده
اطلاعات فایل : زبان فارسی / 10 صفحه / حجم : KB 775
نقد و بررسیها
هنوز بررسیای ثبت نشده است.