Civil.Engineering.Formulas.Pocket.Guide.[taliem.ir]

CIVIL ENGINEERING FORMULAS

ABSTRACT

Many engineers, professional societies, industry associations, and governmental agencies helped the author find and assemble the thousands of formulas presented in this book. Hence, the author wishes to  acknowledge this help and assistance. The author’s principal helper, advisor, and contributor was the late Frederick S. Merritt, P.E., Consulting Engineer. For many years Fred and the author were editors on  companion magazines at The McGraw-Hill Companies. Fred was an editor on Engineering-News Record, whereas the author was an editor on Power magazine. Both lived on Long Island and traveled on the same railroad to and from New York City, spending many hours together discussing engineering, publishing, and book authorship. When the author was approached by the publisher to prepare this book, he turned to Fred Merritt for advice and help. Fred delivered, preparing many of the formulas in this book and giving the author access to many more in Fred’s extensive files and published materials. The author is most grateful to Fred for his extensive help, advice, and guidance.

INTRODUCTION

Civil engineers throughout the world accept both the United States Customary System (USCS) and the System International (SI) units of measure for both applied and theoretical calculations. However, the SI units are much more widely used than those of the USCS. Hence, both the USCS and the SI units are presented for essentially every formula in this book. Thus, the user of the book can apply the formulas with confidence anywhere in the world. To permit even wider use of this text, this chapter contains the conversion factors needed to switch from one system to the other.  For engineers unfamiliar with either system of units, the author suggests the following steps for becoming acquainted with the unknown system: 1. Prepare a list of measurements commonly used in your daily work. 2. Insert, opposite each known unit, the unit from the other system. Table 1.1 shows such a list of USCS units withcorresponding SI units and symbols prepared by a civil engineer who normally uses the USCS. The SI units shown in Table 1.1 were obtained from Table 1.3 by the engineer.

چکیده

بسیاری از مهندسان، جوامع حرفه ای، انجمن های صنعت و ادارات دولتی به پیدا کردن و جمع آوری هزاران فرمول ارائه شده در این کتاب کمک کردند. از این رو، نویسنده مایل است که این کمک و کمک را تأیید کند. کمک کننده اصلی، مشاور و مشارکت کننده، مرحوم فردریک S. Merritt، P.E.، مهندس مشاور بود. برای چندین سال، فرد و نویسنده، ویراستاران مجلات همراه در شرکت McGraw-Hill بودند. فرد یک ویرایشگر در Engineering-News Record بود، در حالی که نویسنده ویرایشگر مجله Power بود. هر دو در لانگ آیلند زندگی می کردند و در همان راه آهن به شهر نیویورک می رفتند و چندین ساعت وقت صرف بحث در مورد مهندسی، چاپ و نشر و انتشار کتاب می کردند. هنگامی که نویسنده توسط ناشر نزدیک شد برای تهیه این کتاب، او به فرد مرییت برای مشاوره و کمک تبدیل شد. فرد ادعا کرد، آماده ساختن بسیاری از فرمولها در این کتاب و دادن دسترسی به بسیاری دیگر از فایلهای گسترده فرد و مواد منتشر شده است. نویسنده به خاطر راهنمایی، راهنمایی و کمک های فراوانش، از فرد بسیار سپاسگزار است.

مقدمه

مهندسان عمران در سراسر جهان، هر دو سیستم عادی ایالات متحده (USCS) و واحد های سیستم System International (SI) را برای هر دو محاسبات کاربردی و نظری پذیرفته اند. با این حال، واحد های SI بسیار بیشتر از USCS استفاده می شود. از این رو، هر دو USCS و واحد SI برای اساسا هر فرمول در این کتاب ارائه شده است. بنابراین، کاربر کتاب می تواند فرمول را با اعتماد به نفس در هر نقطه از جهان اعمال کند. برای اجازه استفاده حتی بیشتر از این متن، این فصل شامل فاکتور تبدیل مورد نیاز برای تغییر از یک سیستم به دیگری است. برای مهندسان نا آشنا با هر یک از سیستم های واحد، نویسنده پیشنهاد می کند مراحل زیر را برای آشنا شدن با سیستم ناشناخته: 1. آماده سازی لیستی از اندازه گیری ها معمولا در کار روزانه شما استفاده می شود. 2. در مقابل هر واحد شناخته شده، واحد از سیستم دیگر قرار دهید. جدول 1.1 چنین لیستی از واحدهای USCS با واحدهای SI و نمادهای آماده شده توسط یک مهندس عمران که معمولا از USCS استفاده می کند را نشان می دهد. واحد های SI که در جدول 1.1 نشان داده شده اند توسط مهندس از جدول 1.3 بدست آمده است.

Year: 2016

Publisher: SPRINGER

By : Tyler G. Hicks, P.E

File Information: English Language/ 480 Page / size: 1.98 MB

Download tutorial

سال : 1395

ناشر : SPRINGER

کاری از : Tyler G. Hicks, P.E

اطلاعات فایل : زبان انگلیسی / 480 صفحه / حجم : MB 1.98

لینک دانلود

0 پاسخ

دیدگاه خود را ثبت کنید

تمایل دارید در گفتگو شرکت کنید؟
نظری بدهید!

دیدگاهتان را بنویسید