توضیحات
چکیده
هدف اصلي اين مقاله معرفي روش هاي كاهنده ي نشست در طراحي گروه شمع و نشان دادن مزاياي نسبي آن در مقايسه با روش سنتي طراحي است. روش طراحي با تحليل فرق دارد. در اين مقاله براي تحليل و مدل سازي خاك از فنر استفاده شده است. در محل تماس جدار جانبي شمع ها تعريف شده Q-Z و T-Z ، P-Y با خاك، در هر گره از سه فنر استفاده شده كه مشخصات فنر ها با توجه به شرايط خاك از روي منحني هاي است، لذا اين روش ساده تحليل گروه شمع نيز در كنار روش شمع هاي كاهنده ي نشست براي طراحي گروه شمع در مقاله ارائه مي شود. براي مقايسه روش هاي جديد و سنتي در طراحي گروه شمع، يك مطالعه ي موردي انجام شده و نتايج حاصل از روش سنتي و شمع هاي كاهنده ي نشست ارائه شده است. اين مقاله نتيجه ميگيرد كه بر خلاف روش سنتي طراحي گروه شمع كه شرايط لازم را جهت استفاده از ظرفيت نهايي شمع ها فراهم نكرده و بسيار محافظه كارانه است، روش جديد طراحي گروه شمع با تعيين تعداد بهينه شمع ها سبب مي شود كه شمع ها و پي گسترده مستقر بر آنها تقريبا به صورت همزمان به مرحله تسليم برسند و طراحي داراي شرايط بهينه اي باشدكه از نظر اقتصادي داراي اهميت است.
مقدمه
استفاده از گروه شمع به عنوان پي در سازه هاي مختلف، از ديرباز متداول بوده است. با توجه به پيچيدگي رفتار شمع، موضوعات مختلف در خصوص شمع همواره مورد تحقيق بوده است. از آنجا كه شمع ها به ندرت به صورت تكي مورد استفاده قرار مي گيرندگروه شمع نقش زيادي در تحقيقات گذشته داشته است، از جمله ميتوان به تحليل گروه شمع تحت بار قائم ، تحليل گروه شمع تحت بار افقي و مقايسه روش سنتي و جديد درتحليل گروه شمع اشاره كرد.شمع هاي كاهنده ي نشست به عنوان يك روش جديد طراحي گروه شمع در سالهاي اخير مورد توجه قرار گرفته است. اين روش جديد طراحي در اقتصادي كردن طراحي گروه شمع تاثير زيادي دارد. البته با توجه به تعداد كم مراجع فني در اين زمينه، مهندسين آشنايي كافي با آن نداشته و در نتيجه روش شمع هاي كاهنده ي نشست هنوز رواج چنداني پيدا نكرده است. در ادامه مقاله به بررسي مزاياي روش شمع هاي كاهنده ي نشست در مقايسه با روش سنتي طراحي گروه شمع پرداخته شده است. روش طراحي با روش تحليل متفاوت است. در هر روش طراحي بايد از روش تحليل مناسب استفاده كرد تا تنشها و تغييرشكلها محاسبه گردد. اين مقاله علاوه بر ارائه روش جديد طراحي، تلاش ميكند روش تحليل ساده اي را معرفي كند كه استفاده كاربردي از آن براي مهندسان حرف هاي به سادگي فراهم باشد.
ABSTRACT
The main objective of this paper is to introduce the method of reducing the size of the design of the candle group and its relative advantages compared to the traditional design method. Design method differs from analysis. In this paper, spring is used to analyze and model soil. In the contact area of the sidewalls, the QZ and TZ, PY with the soil are defined in each node, using three springs, the profile of the springs is according to the soil conditions on the curves, so this simple method of analysis of the pile group is also beside The method of reducing the piles for the design of a candle group is presented in the paper. In order to compare new and traditional methods in the design of the pile group, a case study has been done and the results of the traditional method and the reduction piles of the meeting have been presented. This article concludes that in contrast to the traditional method of designing a pile group that does not provide the necessary conditions for the use of the final capacity of the piles and is very conservative, the new design of the pile group by determining the optimal number of piles makes the piles and extruded Based on them almost simultaneously to the stage of submission, and the design has optimal conditions that are economically important.
INTRODUCTION
The use of the pile group as a pillar in various structures has long been common practice. Due to the complexity of the behavior of the candle, various issues have always been investigated. Since candles are rarely used individually, the candle group has played a large part in past research, including the analysis of the pile group under the Ghaem load, the analysis of the pile group under horizontal load, and the comparison of the traditional and the new method in the analysis of the pile group Pointed out that the diminution of the meeting has been considered as a new method of designing the candle group in recent years. This new design method has greatly influenced the design of the candle group. Of course, due to the small number of technical references in this area, the engineers are not familiar with it, and as a result, the method of reducing the piles of the meeting has not yet become commonplace. In the following, we study the advantages of the method of reducing the seat piles in comparison with the traditional method of designing the candle group. The design method is different from the analysis method. In each design method, an appropriate analysis method should be used to calculate tensions and variations. In addition to presenting a new design method, this paper tries to introduce a simple analysis method that can be easily applied to professional engineers.
Year: 2011
Publisher : Sixth National Congress on Civil Engineering
By : Arefeh Arabian Nejad , Ali Fakhr
File Information: persian Language/ 8 Page / size: 300 KB
Only site members can download free of charge after registering and adding to the cart
سال : 1390
ناشر : ششمین کنـگره ملی مهنـدسی عمـران
کاری از : عارفه عرباني نژاد ، علي فاخر
اطلاعات فایل : زبان فارسی / 8 صفحه / حجم : KB 300
نقد و بررسیها
هنوز بررسیای ثبت نشده است.