توضیحات
چکیده
فريت آلائيده شده 19 2 BaFe12−x(Mn0/5Co0/5Ti) x Oبا تركيب x= 1.2.3بوسيله فرآيند سل – ژل بادمايي به مراتب پايين تر از روش هاي مرسوم توليد سراميك ها تهيه گرديد. پودرهاي فريت بدست آمده داراي شكل هگزاگونال و بخوبي از يكديگر جدا مي باشند. براي آناليز ساختارها و خواص مغناطيسي پودرهاي توليد شده از آناليز سنج حرارتي ، تفرق ، xميكروسكوپ الكتروني روبشي (SEM) و دستگاه VSMاستفاده گرديد . نتايج نشان مي دهد كه براي تمامي نمونه ها ساختار فريت نوع Mشكل گرفته است . نمونه هاي با 3و x= 2داراي ميدان پسماند زداي بيشتري مي باشند.
مقدمه
در سالهاي اخير ، هگزا فريت باريم نوع ( BaFe12O19 ) Mبه دليل اهميت آن به عنوان آهنرباي دائمي و ابزار ضبط مغناطيسي با چگالي ضبط بالا ، به شدت مورد توجه و مطالعه قرار گرفته است. در برخي از كاربردهاي صنعتي، موادي با همگني بالا ، شكل ومورفولوژي مناسبي كه رفتار مغناطيسي را به خوبي كنترل كند، مورد نياز است . روش آماده سازي نيز بر خواص ساختاري و مغناطيسي تاثير مي گذارد . تكنيك سل – ژل به عنوان يك روش جديد براي سنتز فريت باريم به كار مي رود. در اين روش،ذرات تك با فاز اندازه دانة در مقياس ميكرومتر و توزيع اندازه دانه باريك در مدت زمان كوتاهي توليد مي گردد. در مقايسه بين فريت ها با ساختارهاي اسپينل و گارنت ، فريت با ساختار هگزاگونال از لحاظ خواص مغناطيسي ناهمسانگردتر است و داراي ناهمسانگردي مغناطوكريستالي ذاتي بزرگتر مي باشد. در روش هاي سراميكي متداول براي تهيه فريت باريم نوع ، Mاحتياج به دماي تف جوشي بالا(بطور معمول تقريباً 1300−1400 0C) براي واكنش حالت جامد مي باشد كه اغلب منجر به شكل گيري فريت درشت دانه مي گردد. اين توده ي غير همگن معمولاً با پروسه ي آسيا كاري تحت خرد شدن قرار مي گيرد و به مقياس ميكروسكوپي با ايجاد كرنش بسيار زياد در شبكه مي رسد. در اين مقاله رابطه بين خواص مغناطيسي و ريز ساختار 19 گزارشBaFe12−x (Mn0/ 5Co0/ 5Ti) x O شده است . براي رسيدن به همگني يون ها در سطح اتمي ، فريت باريم آلائيده شده با Mn-Co-Tiبوسيله ي روش سل – ژل سنتز گرديد و خواص مغناطيسي و مشخصات ريز ساختاري آن مورد بررسي قرار گرفت.
ABSTRACT
The doped ferrite 19 2 BaFe12-x (Mn0 / 5Co0 / 5Ti) x O with compound x = 1.2.3 was prepared by the sol-gel process far below the conventional ceramic production methods. The obtained ferrite powders have a hexagonal shape and are well separated from each other. To analyze the magnetic structure and properties of the powders produced by the thermal analysis, scattering, x-scanning electron microscopy (SEM) and VSM device. The results show that the M-type ferrite structure is formed for all specimens. Samples with 3 and x = 2 have more deformation field.
INTRODUCTION
In recent years, the BaFe12O19 M Hexa-Frit has been heavily studied and studied due to its importance as a permanent magnet and magnetic recording equipment with high recording density. In some industrial applications, high-homogeneity materials are required to form an appropriate morphology that can control the magnetic behavior well. The preparation method also affects the structural and magnetic properties. The cell-gel technique is used as a new method for the synthesis of barium ferrite. In this method, single-phase particles with size of a micrometer scale and small grain size distribution are produced in a short time. In a comparison between the ferrites with the spinel and garnet structures, the hexagonal structure of the ferrite is more anisotropic in terms of its magnetic properties and has a larger intrinsic magnetocrystalline anisotropy. In typical ceramic methods for the preparation of a barium-type ferrite, M requires high spit-temp (typically about 1300-1400 ° C) for solid state reactions, which often leads to the formation of coarse ferrite. This non-homogeneous mass is usually subjected to an Asian process under crushing, and it reaches the microscopic scale by creating a very high strain on the network. In this paper, the relationship between the magnetic properties and the microstructure of BaFe12-x (Mn0 / 5Co0 / 5Ti) x O is reported. To achieve the homogeneity of ions at the atomic level, the barite ferrite melted with Mn-Co-Ti was synthesized by the sol-gel method, and its magnetic properties and microstructural characteristics were investigated.
Year: 2007
Publisher : 11th National Congress of metallurgy of Iran
By : Abbas Torshizi, Mohammad Sadegh Rashidi, Ali Ghasemi
File Information: persian Language/ 10 Page / size: 1,53 KB
سال : 1386
ناشر : يازدهمين كنگره ملي مهندسين متالورژی ايران
کاری از : عباس ترشيزي , محمد صادق رشيدي , علي قاسمي
اطلاعات فایل : زبان فارسی / 10 صفحه / حجم : KB 1,53
نقد و بررسیها
هنوز بررسیای ثبت نشده است.