توضیحات
چکیده
در اين تحقيق با بهره گيري از درصدهاي مختلف آميژان هاي Al-5Ti-1Bو ، Al-5Zrاندازه دانه، DASو مورفولوژي دانه آلياژ آلومینیوم 7075مورد بررسي قرار گرفته است. نتايج نشان مي دهد که با افزايش درصد اين مواد جوانه زا اندازه دانه تا مقدار معيني کاهش يافته ولي تاثیرتیتانیم در کاهش اندازه دانه چشمگير است.نتایج بدست آمده همچنين نشان داد که اندازه فاصله بازو هاي دندريتي ثانويه تغييرات محسوسي نداشتند ولي مورفولوژي دانه ها دستخوش دگرگوني شده که بيشتر با افزايش تیتانیم این امر صورت ميگیرد.
مقدمه
آلياژهاي سري 7xxxآلياژهايي با استحکام و مدول يانگ بالا و همچنين دانسيته پايين مي باشند که اين ويژگي ها باعث افزايش کاربرد آنها در صنايع هوافضا شده است. از مهمترين آلياژهاي اين رده، آلياژ 7075 می باشد که حاوي 5/1تا 6/1درصد روي، 2/1تا 2/9درصد منيزيم و 1/2تا 2/0درصد مس است. اين آلياژ داراي خواصي چون شکل پذيري و استحکام بالا به همراه مقاومت به خوردگي خوب مي باشد. آلياژهاي Al-Zn-Mg- Cuقابليت رسيدن به استحکام بالاتر را از طريق پيرسختي و کنترل ريزساختار دارا هستند. کنترل ريزساختار از طريق عوامل زير حاصل مي شود : 1)تغيير ترکيب شیمیایی 2) به حداقل رساندن ناخالصي هايي نظير آهن و سيليسيم 3) عمليات ترمومکانيکي و 4) استفاده از عوامل جوانه زا اصولا در انجماد آلياژها امکان وقوع سه نوع مورفولوژي وجود دارد : دندريتي، رزشکل و گلبولي. سه منطقه از اين دانه ها نيز در شمش هاي تکباري ديده مي شود که عبارتند از : هم محور تبريدي، ستوني و هم محور مرکزي. جهت دست يابي به خواص مطلوب ، دانه ها بايد تحت کنترل قرار گيرند. در بيشتر مواقع منطقه ستوني و دانه هاي دندريتي روي خواص تاثير منفي ي م گذارند. از طرفي ايجاد دانه هاي هم محور به جاي ستوني ي م تواند باعث يکنواخت شدن خواص، کاهش تمايل به ترک گرم و حفرات انقباضي، بهبود قابليت ماشين کاري و توزيع مناسب فازها گردد يک. ي از روش هاي مناسب حذف منطقه ستوني وایجاد ساختار هم محور با استفاده از عوامل جوانه زا مي باشد. در اين مقاله به بررسي تاثير عوامل جوانه زاي حاوي Ti-Bو Zrبر روي اندازه و مورفولوژي دانه ها و همچنين فاصله بين بازوهاي دندريتي ثانويه پرداخته شده است.
ABSTRACT
In this research, using different percentages of Al-5Ti-1B amines, Al-5Zr grain size, DAS and 7075 aluminum alloy grain morphology have been investigated. The results show that by increasing the percentage of these germinating materials, the grain size is reduced to a certain amount, but its effect on reducing the size of the seeds is significant. The results also showed that the size of the distance between the secondary dendritic arms did not change significantly, but the morphology of the seeds undergoes metamorphism This is due to the increase in titanium.
INTRODUCTION
7xxx series alloys have high strength and high modulus and low density modulus, which have increased their application in the aerospace industry. One of the most important alloys in this category is the 7075 alloy containing from 1.5 to 1.6% zinc, 1.2 to 9.2% magnesium and 1-2% to 0.2% copper. It has properties like high ductility and strength with good corrosion resistance. Al-Zn-Mg-Cu alloys have the ability to achieve higher strength through microstructure and microstructure control. Microstructure control is achieved by: 1) changing the chemical composition 2) minimizing impurities such as iron and silicon 3) thermo-mechanical operations and 4) using germinating agents. There are three types of morphology in the solidification of alloys: Dendritic, Distilled and Rabbolic. The three regions of these grains are also found in single bolts, which include: axis of refrigeration, column and central axis. Seeds should be controlled to achieve optimal properties. In most cases, the pillar region and dendritic grains influence the properties negatively. On the other hand, the creation of coaxial grains instead of columns can result in uniformity of properties, reduction of the tendency to leave warm and contraction cavities, improve machinability and appropriate distribution of phases. One of the appropriate methods is the removal of the pillar region and the creation of a co-axial structure using germination factors. In this paper, the effect of germinating factors containing Ti-B and Zr on the size and morphology of the seeds and the distance between the secondary dendritic arteries has been investigated.
Year: 2017
Publisher : 11th National Congress of metallurgy of Iran
By : Mohsen Baghernezhad, Yousef Haj Karim Kharrazi, Saeed Rastegari, Reza Labaf
File Information: persian Language/ 12 Page / size: 453 KB
سال : 1396
ناشر : يازدهمين كنگره ملي مهندسين متالورژی ايران
کاری از : محسن باقرنژاد ،يوسف حاج كريم خرازي ، سعيد رستگاري، رضا لباف
اطلاعات فایل : زبان فارسی / 12 صفحه / حجم : KB 453
نقد و بررسیها
هنوز بررسیای ثبت نشده است.