توضیحات
چکیده
استفاده گسترده از ورقهاي فولادي كم كربن جهت اهداف كششي و كشش عميق در صنايع مختلف و بخصوص در خودروسازي به عنوان بدنه خودرو، بعلاوه تمايل به استفاده از ورقهاي نازكتر جهت سبكتر كردن خودرو، ايجاب ميكند پروسه توليد ورق چنان تنظيم شود كه به رغم كاهش ضخامت ورق، استحكام و قابليت فرم پذيري آنها حفظ شود. آخرين مرحله كاهش ضخامت ورقهاي فولادي معمولاً با نورد سرد صورت ميگيرد. در اين فرايند سختي و استحكام ورق افزايش و قابليت شكل پذيري آن كاهش مييابد، لذا لازم است از طريق يك عمليات ترمومكانيكي مناسب خواص ورق اعاده شده و تركيب استحكام و داكتيليتي به حد مطلوب برسد. در اين پژوهش، نمونه هاي يك ورق فولادي كم كربن پس از اعمال نورد سرد در دماهاي 700°C ،650°C ،600°Cو 750°Cبه مدت 20دقيقه آنيل و سپس در سه محيط كوره، هوا و آب سرد شدند. بررسيهاي ميكروسكوپ نوري و تست هاي كشش نشان دادند كه كاهش سرعت سرد شدن منجر به بهبود خواص فرمپذيري ميشود. بهترين شكلپذيري پس از آنيل در 650-700°Cو سرد شدن در كوره، حاصل شد. اين پديده به كامل شدن تبلورمجدد و كاهش تنش هاي باقيمانده و دانسيته نابجايي ها طي سرمايش آهسته در كوره نسبت داده ميشود.
مقدمه
فولادهاي كم كربن جزو مناسب ترين مواد جهت اهداف كششي و كشش عميق هستند . هر فلزي كه توسط پروسه نورد به ورق تبديل شده، بايد به اندازه كافي داكتيل باشد تا قابليت كشش عميق داشته باشد. ورقهايي كه نورد سرد شده اند براي اينكه قابليت كشش عميق داشته باشند بايد عاري از اثرات كارسرد باشند. بطوركلي پس از ريخته گري شمش فولادي، ضخامت آن با نورد گرم كاهش داده شده و در ادامه توسط نورد سرد محصولاتي نظير تسمه يا ورق توليد ميشود . پارامترهاي مختلفي بر نيروي نورد سرد اثر گذار است، ضميري و اكبرزاده نشان دادند كه در نورد گرم، هرچه كه دماي كلاف پيچي بالاتر باشد نيروي مورد نباز براي نورد سرد كمتر خواهد شد. با نورد سرد دانه ها كشيده شده، سطوح فصل مشترك دانه ها افزايش يافته، دانسيته نابجايي و عيوب زياد مي شود و انرژي دروني ورق افزايش مييابد و طي اتفاقات مذكور، استحكام ورق افزايش يافته و از داكتيليتي آن كاسته مي شود. و در نتيجه خواص مناسب براي كشش عميق و اتساع را نخواهد داشت.
ABSTRACT
The widespread use of low carbon steel plates for tensile and tensile applications in various industries, especially in automobile manufacturing, as well as the tendency to use thinner sheets to lighten the vehicle, requires that the sheet production process be adjusted so that, despite the reduction in thickness Sheet, strength and elasticity are preserved. The last step in reducing the thickness of steel sheets is usually made with cold rolling. In this process, the hardness and strength of the sheet increases and its ductility decreases; therefore, it is necessary to achieve the optimum properties of the sheet and the combination of strength and ductility through an appropriate thermomechanical operation. In this study, samples of a low carbon steel sheet were cooled in cold furnaces, air and water at cold temperatures of 700 ° C, 650 ° C, 600 ° C and 750 ° C for 20 minutes. Light microscope studies and tensile tests showed that reducing the cooling rate leads to improvement of formability properties. The best formability was obtained after annealing at 650-700 ° C and cooling in the furnace. This phenomenon is attributed to the completion of crystallization and reduction of residual stresses and the density of dislocations during a slow cooling in the furnace.
INTRODUCTION
Low carbon steels are among the most suitable materials for tensile and deep drawing purposes. Any metal that has been converted by rolling process into a sheet should be sufficiently ductile to have a deep drawing capacity. Cold rolled sheets should be free from impacts in order to be able to draw deep. In general, after casting of steel ingots, its thickness is reduced by hot rolling, and then produced by cold rolling of products such as belt or sheet. Various parameters affect the cold rolling force, Zamiri and Akbarzadeh showed that in hot rolling, the higher the bending temperature would be, the lower the force for cold rolling would be less. With cold rolled grains, the grain boundary levels are increased, the density of dislocation and defects increase, and the internal energy of the sheet increases, and during these events, the sheet strength increases and its ductility decreases. And thus does not have the proper properties for deep drawing and dilation.
KB 374 :اطلاعات فایل : زبان فارسی / 10 صفحه / حجم
نقد و بررسیها
هنوز بررسیای ثبت نشده است.